Kenth Kenth is offline

Ultimate Warrior

Visitor Messages

Showing Visitor Messages 1 to 4 of 4
  1. Scott Thelander
    08-16-2017 10:10 AM
    Scott Thelander
    Hello

    I have an original ...15.00 scott
  2. Kenth
    11-03-2009 01:54 PM
    Kenth
    Hi!
    Is the carb going back to the original engine?

    Stock jetting for #7042264 is jets stamped #74, primary rods stamped #47, secondary rods #7045923 stamped CR with 5/8 turn preload on airvalve spring. #7037305 power piston spring.
    Float setting 3/8".
    Pump rod location, inner.
    Fast Idle (bench) 2-turns, on high step.
    Fast Idle Rpm, 1500-N 2:nd step hot engine, choke off.
    Vacuum break .195".

    If your engine is modified with a hotter than standard camshaft, the carbs idle circuit WILL have to be modified/adjusted to the new lower vacuum signal the hotter cam provides.

    After setting the idle mixture needles for best lean idle, approximately 2.5 turns out from lightly seated, you may do the "tip-in" test. Slowly close the choke-blade and note the first change in rpm before the engine chokes. If you´re close there would be no change before the engine chokes, if rpm drops idle circuit is too rich (rarely happens), if rpm increase the idle circuit may be lean.
    Then set the fast idle cam on high step, use the fast idle screw to set 2200rpm´s, do the "tip-in" again, here you will notice a 50-150 rpm increase wich indicates a close to proper cruise mixture.
    Rpm decrease here indicates a too rich mixture, again rarely happens with original jetting, more than 200 rpm increase indicates a too lean mixture and smaller/richer primary rods will be needed.

    Hope this helps some......

    Greetings,
    Kent
  3. Dustin68
    11-03-2009 09:32 AM
    Dustin68
    Hi!
    A member on the board suggested I send my question to you regarding quadrajets:
    I just rebuilt a 72 q-jet 7042264 using Cliffs book and rebuild kit. What I cant seem to find is the data table for stock settings on this carb. Anyone know of a source?
    BTW...I have 48 primary metering rods, CS secondarys, 74 jets, N hanger, not sure which spring to use in the power piston or what the float level is supposed to be (I started with 1/4").
    Want to get this thing as close as I can before I try it out on the engine. Cliff said that a stock rebuild would be good start for my altitude as this was a lean Califonia carb.
    Thanks!
  4. Svante 400
    08-30-2009 12:48 PM
    Svante 400
    Tjena Kenth, mycket folk blir det den 19/9. regards from Svante 400

About Me

  • About Kenth
    Cars
    1966 GTO Tripower, 1970 GTO TheJudge
    Location
    The Kingdom of Sweden
    Interests
    Pontiacīs, restoring, driving, numbers crunching.
  • Signature
    1966 GTO Tri-Power
    1970 GTO TheJudge
    http://www.poci.org/
    http://gtoaa.org/

Statistics

Total Posts
Visitor Messages
Total Thanks
General Information
  • Last Activity: Today 03:15 PM
  • Join Date: 02-04-2003
  • Referrals: 1

Friends

Showing Friends 1 to 2 of 2

All times are GMT -4. The time now is 05:20 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017