Tim Corcoran Tim Corcoran is offline

Ultimate Warrior

Visitor Messages

Showing Visitor Messages 1 to 10 of 32
  1. DCVING
    07-21-2023 11:16 AM
    DCVING
    I believe I may now have this camshaft. Not sure of all the specs on it as the member on here I got it from lost the specs. Is it possible you may still have them?

    Lunati Solid Roller Cam $150.00
    This is a very effective single pattern cam. In Bill Takanabe's 65 GTO with a 455 and #16 D-ports ran consistent 10.30’s

    Advertised Duration 317/317
    Duration @.050 284/284
    Lobe Lift .404/.404
    Lift @ 1.5 rocker .606/.606
    LSA 104
    Valve lash .024 Hot
    I have a copy of the spec sheet from Lunati
  2. Tim Corcoran
    11-07-2022 06:07 PM
    Tim Corcoran
    I have a few sets of solid lifters left
  3. glenn911
    10-29-2022 09:25 AM
    glenn911
    Hi Tim, are you still selling Hylift/Johnson lifters? Thanks Eric
  4. Tim Corcoran
    11-16-2015 08:59 AM
    Tim Corcoran
    No problem I got them if you need them. Glad your problem is resolved.
  5. bobby326
    11-15-2015 01:14 PM
    bobby326
    Hello Tim. I sent you a message last night about lifters. Im sorry but i dont need them. I was going to change cams but i ended up tweeking a few things and now everything seems to be ok now. Sorry for the inconvenience. Thank you Bobby
  6. Tim Corcoran
    08-25-2015 11:53 AM
    Tim Corcoran
    Yes I have one new in the box. Please email me if interested. tim.corcoran99@gmail.com
  7. 87PONT.TA
    08-24-2015 09:22 PM
    87PONT.TA
    hope I have the right guy. J/C said you might have a mega brace for sell?
  8. Tim Corcoran
    07-23-2015 07:52 PM
    Tim Corcoran
    I don't mind starting a **** storm because it alerts other unsuspecting guys from a disaster. I posted my experience on the venders experience board in PY. They guy is an ass hole.
  9. 67GTONUT
    07-20-2015 02:46 PM
    67GTONUT
    Tim..... Been there, done that..... Guy has an HEI from me for over 2 years.... wont respond to emails or phone calls..... He can ****ing drop dead for all I care at this point. Only good thing is... it was just a core that I wanted built.... so I almost no money in that deal.... Thanks for the heads up, I wish we could warn everyone without creating a ****storm on the board.... Be Well, Troy
  10. 66GTOxx
    03-09-2015 09:57 PM
    66GTOxx
    Hi Tom,
    Thank you.

    I have all the sizes and everything, but not having the exact offset wheel and tire on hand its impossible to guess what will fit an odd shaped wheelwell such as these. Its easy to err on the small side and end up where you could have had another 1/2" of tire on the car if you had a checker wheel to start with, but I don't have a 5" offset wheel here. I appreciate the info. I'm just not up on everything on these GTO's and particular Pontiac issues. I do chassis work, fabrication and welding and body work. I usually can figure anything out if I just have some basic parameters. If you're familiar with Larry Quinns Blast from the Past, I built the chassis , all the new 4 link and fab9 rear,etc.......and Hooter Brad Shoemakers Iron Indian Tempest...I built that chassis, done the fab'ing, , tinwork, bodywork, stretched the quarters, mounted the body and painted it.....Brad done all the final and drivetrain assembly. Also John Grinwalds NSS Thunderbolt chassis, and lots of other local cars chassis, narrowing, and backhalfs, nostalgia funny car chassis work, etc. Im currently building a series of correct 66-67 vintage front engine dragsters with nitro 392 hemis. Not to brag....its just that when you have low post count people sometimes don't know how much experience someone has. Things either fit or they don't and I don't guess without knowledge. This is what I do full time. I'm working on an album of a lot of this to link to. I just don't have a problem with asking a question on some things I'm not into daily. Used to work at a local race engine shop back in 84-86, been building motors ever since, but have only built 3 relatively stock Pontiacs and those were a few years ago, so I'm playing catch up on current parts and tricks. Was thinking about getting some Johnson lifters (do they make edm hole oiler type?) from you for use on possibly Crower 60310 or 11, but seen where you aren't messing with any right now, I hope everything is going to be ok for you all. Thanks, Brian

About Me

  • About Tim Corcoran
    Cars
    65 Pontiac LeMans, 67 Pontiac LeMans
    Location
    Willow Spring, North Carolina
    Interests
    Pontiac drag racing
    Occupation
    Aviation Consultant
  • Signature
    Tim Corcoran

Statistics

Total Posts
Visitor Messages
Total Thanks
General Information
  • Last Activity: Today 01:12 PM
  • Join Date: 01-09-2000
  • Referrals: 0

All times are GMT -4. The time now is 10:05 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017