Forum: Pontiac - Street
Today, 04:06 PM
|
Replies: 12
Views: 277
|
Forum: 67-69 Firebird TECH
Today, 01:35 PM
|
Replies: 4,573
Views: 789,858
|
Forum: THE LOBBY
Today, 12:41 PM
|
Replies: 3
Views: 109
My only suggestion is to be an active seller,...
My only suggestion is to be an active seller, answer any question to the best of your ability. I understand that they usually give the sellers a very short notice when their auctions go live, I hope...
|
Forum: THE LOBBY
Today, 10:37 AM
|
Replies: 77
Views: 4,614
|
Forum: THE LOBBY
Today, 10:14 AM
|
Replies: 3
Views: 109
|
Forum: Pontiac - Street
Today, 09:46 AM
|
Replies: 173
Views: 7,825
|
Forum: Pontiac - Street
Today, 09:40 AM
|
Replies: 12
Views: 277
|
Forum: Pontiac - Street
Today, 08:26 AM
|
Replies: 27
Views: 727
Evolutions should be able to handle that. They...
Evolutions should be able to handle that. They can likely handle more aggressive profiles like an XFI at those pressures, but I think something like an XFI might be getting on the edge of what they...
|
Forum: Pontiac - Street
Today, 05:40 AM
|
Replies: 75
Views: 3,012
|
Forum: Pontiac - Street
Today, 02:58 AM
|
Replies: 33
Views: 726
|
Forum: THE LOBBY
Yesterday, 11:50 PM
|
Replies: 6
Views: 357
|
Forum: Pontiac - Street
Yesterday, 11:47 PM
|
Replies: 10
Views: 205
|
Forum: Pontiac - Street
Yesterday, 10:29 PM
|
Replies: 27
Views: 727
As far as seat and open pressures on a mild...
As far as seat and open pressures on a mild hydraulic roller like that, especially a pontiac, 150 or so on the seats is pretty normal, and usually close to 400 open just for the simple reason the...
|
Forum: Pontiac - Street
Yesterday, 10:20 PM
|
Replies: 33
Views: 726
|
Forum: THE LOBBY
Yesterday, 09:52 PM
|
Replies: 6,149
Views: 611,053
|
Forum: THE LOBBY
Yesterday, 09:20 PM
|
Replies: 6,149
Views: 611,053
|
Forum: Pontiac - Street
Yesterday, 08:23 PM
|
Replies: 12
Views: 277
Inside HEI module
Well i had 5 used HEI modules so i put a spare dist in a vice hooked up power to test.....two didnt make the grade... one was a 990 unit its the one more intact i cut it open with a small rotary...
|
Forum: Pontiac - Street
Yesterday, 06:05 PM
|
Replies: 9
Views: 317
I built a 428 with 13 heads a long time ago. I...
I built a 428 with 13 heads a long time ago. I want to say late 90's. Back when dad was swapping blocks and cranks around we ended up with a 428 crank laying around so I had it ground to fit 400...
|
Forum: Pontiac - Street
Yesterday, 05:56 PM
|
Replies: 9
Views: 317
|
Forum: Pontiac - Street
Yesterday, 05:00 PM
|
Replies: 33
Views: 726
Spot on I believe
Pretty sure this is my exact problem. That was actually my next step. When I did the tune I wasn’t factoring in the heat soak. So I’m gonna put the 185 thermostat back in move my fuel lines and use a...
|
Forum: Pontiac - Street
Yesterday, 04:45 PM
|
Replies: 33
Views: 726
The sniper runs the fan in stall and crank?
...
The sniper runs the fan in stall and crank?
I guess that would create a pretty easy test for the OP. When the engine is off and heat soaked, disable the fan in the ecu, then attempt to start.
|
Forum: Pontiac - Race
Yesterday, 04:37 PM
|
Replies: 5
Views: 259
Wow.
Thanks.
They appear to match the rods...
Wow.
Thanks.
They appear to match the rods on the RPM web site exactly.
RPM no longer carries this size and they also no longer carry standard length Pontiac rods either.
I will weigh them...
|
Forum: Pontiac - Street
Yesterday, 04:07 PM
|
Replies: 27
Views: 727
|
Forum: Pontiac - Street
Yesterday, 04:06 PM
|
Replies: 27
Views: 727
|
Forum: Pontiac - Street
Yesterday, 03:25 PM
|
Replies: 33
Views: 726
|