Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Showing results 1 to 10 of 10
Search took 0.03 seconds. Search: Posts Made By: hgerhardt
Forum: Pontiac - Street 02-21-2024, 09:10 PM
Replies: 21
Views: 1,199
Posted By Schurkey
...and a thicker head gasket kills quench/squish,...

...and a thicker head gasket kills quench/squish, also leading to potentially more knock/ping.
Forum: Pontiac - Street 08-08-2023, 12:09 PM
Replies: 398
Views: 70,381
Posted By 1969GPSJ
Franked, for what it's worth, I would hate to...

Franked, for what it's worth, I would hate to see you end up unhappy with your build, but these are just educated opinions, experiences and keyboard warrior stuff on the forum - maybe we are right,...
Forum: THE LOBBY 07-12-2023, 12:43 PM
Replies: 67
Views: 9,952
Posted By Dave Bisschop
Thank you everyone for your words of concern and...

Thank you everyone for your words of concern and encouragement. The past month has been a tough one for my entire family as it was a lot more than just the business that burned to the ground on June...
Forum: Pontiac - Street 07-05-2023, 02:00 PM
Replies: 37
Views: 1,797
Posted By Vetteman61
It's been quite a few years ago, but from what I...

It's been quite a few years ago, but from what I remember it was due to the fact that the old glass fuses didn't make great contact and had a tendency to get hot and melt the plastic (or possibly...
Forum: Pontiac - Street 03-06-2023, 08:45 PM
Replies: 33
Views: 2,187
Posted By lust4speed
The front pulleys are made for a wider belt, and...

The front pulleys are made for a wider belt, and if the belt rides too deep in the wider grooves it could ride on the bottom flat of the pulley. Without getting specific on belt numbers, mine takes...
Forum: Pontiac - Street 01-14-2023, 08:31 AM
Replies: 5
Views: 720
Posted By graygator
Consider using parts from a 98-02 Camaro or...

Consider using parts from a 98-02 Camaro or Firebird. They have built in e-brakes. You may have to shim each side differently and as needed to center the caliper on the rotor. I put this swap on the...
Forum: THE LOBBY 12-30-2022, 07:47 PM
Replies: 79
Views: 9,162
Posted By 242177P
This all could've been avoided if they had bought...

This all could've been avoided if they had bought a fifth wheel camper

https://forums.maxperformanceinc.com/forums/attachment.php?attachmentid=604291&stc=1&d=1672443966
Forum: Pontiac - Street 12-20-2022, 06:04 PM
Replies: 24
Views: 2,515
Posted By ScottP
I know this is an old thread, but its my old...

I know this is an old thread, but its my old thread so I think that makes it OK<g>

After almost 6 years of running the serpentine setup just as you see in the first
few posts, I finally got...
Forum: THE LOBBY 06-11-2022, 09:47 PM
Replies: 26
Views: 3,598
Posted By Tom Vaught
A very good FRIEND (who is not

an Engineer) sent this to me today.



Understanding Engineers



Two engineering students were riding bicycles across a university campus when one said to the other, "Where did you get the...
Forum: Heating & Cooling TECH 06-03-2022, 02:58 AM
Replies: 9
Views: 2,420
Posted By gto4ben
Can you perform a more detailed measurement of...

Can you perform a more detailed measurement of inlet pressure vs low side pressure. using your gauges? There should be a "knee" at the point the POA begins regulating. If your "knee" is there but at...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -4. The time now is 01:37 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017