Forum: THE LOBBY
04-14-2024, 10:31 PM
|
Replies: 452
Views: 32,434
|
Forum: Pontiac - Street
01-28-2024, 10:20 PM
|
Replies: 19
Views: 1,143
|
Forum: Pontiac - Street
01-19-2024, 06:50 PM
|
Replies: 18
Views: 1,874
If you want it to look original, you would want...
If you want it to look original, you would want to run a new resistor wire if it was cut off. I'm not sure if those are available aftermarket by themselves. I suppose you could find a parts harness...
|
Forum: Pontiac - Street
01-15-2024, 04:29 PM
|
Replies: 7
Views: 755
|
Forum: Pontiac - Street
01-05-2024, 11:56 AM
|
Replies: 3
Views: 451
|
Forum: Pontiac - Street
01-02-2024, 03:44 PM
|
Replies: 51
Views: 2,917
|
Forum: Pontiac - Street
11-07-2023, 08:05 PM
|
Replies: 10
Views: 595
|
Forum: Pontiac - Street
11-07-2023, 05:33 PM
|
Replies: 10
Views: 595
|
Forum: Exhaust TECH
06-22-2023, 11:33 PM
|
Replies: 3
Views: 936
Ram Air exhaust manifold outlet repair
I have a set of 1967 HO exhaust manifolds that I’m running on my car and one had a problem with the outlet bevel rusting away, creating an exhaust leak. I was out of ideas as to how to get it to seal...
|
Forum: 71-77 Ventura including 74 GTO TECH
06-21-2023, 02:16 AM
|
Replies: 6
Views: 1,836
Just for future reference, in case questions...
Just for future reference, in case questions about X body sport mirrors ever comes up again, the X body sport mirrors are not stud mount. They have a mounting bracket that attaches to the door. It is...
|
Forum: Pontiac - Street
06-13-2023, 11:56 PM
|
Replies: 51
Views: 2,526
If you are talking about the 744 cam, it idles...
If you are talking about the 744 cam, it idles with a very slight loap in a 10:1 433 that I have. I would imagine that it would idle pretty smooth in a 461. It runs well and it produces plenty of...
|
Forum: Pontiac - Street
05-04-2023, 03:01 PM
|
Replies: 52
Views: 3,011
|
Forum: Pontiac - Street
05-02-2023, 12:43 PM
|
Replies: 52
Views: 3,011
Oil Pump Shaft
Thought I would share a picture of my new oil pump driveshaft that came out of my 428. It is a Melling pump shaft. I just got the engine running the first of April. The first start went well and...
|
Forum: Pontiac - Street
04-29-2023, 02:06 AM
|
Replies: 104
Views: 5,308
I have a 428 that had a problem with the rear...
I have a 428 that had a problem with the rear cap. I brought the block and a 455 rear cap to a machine shop and they were able to make the other rear cap work. They pulled the dowels in the block,...
|
Forum: THE LOBBY
04-05-2023, 08:49 PM
|
Replies: 128
Views: 9,542
Here is a picture of a Studebaker with a 389...
Here is a picture of a Studebaker with a 389 tripower. It was owned by Bill Morgan, who used to post here quite a bit.
Here is a link to Bill’s write up about the car. Always enjoyed reading...
|
Forum: THE LOBBY
04-05-2023, 11:05 AM
|
Replies: 128
Views: 9,542
|
Forum: The Body Shop TECH
03-07-2023, 06:46 PM
|
Replies: 74
Views: 8,822
|
Forum: The Body Shop TECH
02-23-2023, 06:02 PM
|
Replies: 74
Views: 8,822
|
Forum: Pontiac - Street
12-29-2022, 05:08 PM
|
Replies: 22
Views: 2,198
|
Forum: THE LOBBY
12-15-2022, 01:35 PM
|
Replies: 69
Views: 4,989
|
Forum: Pontiac - Street
12-14-2022, 05:02 PM
|
Replies: 26
Views: 2,097
|
Forum: Pontiac - Street
10-17-2022, 10:48 AM
|
Replies: 108
Views: 8,404
I have had good luck with the Summit 2801 and...
I have had good luck with the Summit 2801 and Crower 60240 camshafts in 8:1-9:1 compression engines. For me, both of these camshafts resulted in a smooth idle, good low-end power and made for a...
|
Forum: Pontiac - Street
09-17-2022, 10:37 AM
|
Replies: 51
Views: 4,010
|
Forum: Pontiac - Street
09-17-2022, 12:09 AM
|
Replies: 51
Views: 4,010
I will take a look and see. This engine had 6H...
I will take a look and see. This engine had 6H heads, still have them. I knew of the car it came out of and the engine had never been into to my knowledge. It still had the GM bearings in it. My 75...
|
Forum: Pontiac - Street
07-20-2022, 11:05 AM
|
Replies: 22
Views: 1,766
If you are running stock style 389 pistons,...
If you are running stock style 389 pistons, you'll probably want to check your piston to valve clearance since the valve reliefs on a 389 piston are designed for a different valve angle than your 62...
|