Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Page 1 of 3 1 23
Showing results 1 to 25 of 67
Search took 0.01 seconds. Search: Posts Made By: FNFGTO
Forum: Members Helping Members 08-31-2007, 07:51 AM
Replies: 10
Views: 499
Posted By FNFGTO
New pads & rotors. Noise was there before and...

New pads & rotors. Noise was there before and after.
Forum: Members Helping Members 08-30-2007, 10:51 PM
Replies: 10
Views: 499
Posted By FNFGTO
What else do you think? CV jounts on short...

What else do you think? CV jounts on short shafts? Dunno!
Forum: Members Helping Members 08-30-2007, 09:58 PM
Replies: 10
Views: 499
Posted By FNFGTO
4X4, makes an awful sqweel on drivers side when I...

4X4, makes an awful sqweel on drivers side when I turn sharp right!
Forum: Members Helping Members 08-30-2007, 09:42 PM
Replies: 10
Views: 499
Posted By FNFGTO
2001 GMC Yukon wheel bearing replacement

Anybody ever replace the front bearings on a 2001 GMC Yukon?
Forum: Electrical Tech 12-09-2006, 10:36 PM
Replies: 5
Views: 200
Posted By FNFGTO
Thanks again, George. I'll keep them for future...

Thanks again, George. I'll keep them for future reference.

John
Forum: Electrical Tech 12-09-2006, 11:11 AM
Replies: 5
Views: 200
Posted By FNFGTO
OK so after checking everything over again I...

OK so after checking everything over again I tried something else. I replaced the 25 amp fuse. Guess what? It works like a charm. Can a stupid $.39 fuse have caused all these problems? Maybe poor...
Forum: Electrical Tech 12-07-2006, 01:27 PM
Replies: 5
Views: 200
Posted By FNFGTO
Thanks George. Once again the Guru of the...

Thanks George. Once again the Guru of the electrical world steps up to help a PY brother.
Forum: Electrical Tech 12-07-2006, 01:08 PM
Replies: 5
Views: 200
Posted By FNFGTO
Any GM techs out there?

OK it's not a Pontiac question because I can fix most electrical problems on my GTO. Here goes, the vehicle is a 2001 GMC Yukon. Rear wiper running really slow and finally died. Replaced wiper motor...
Forum: The Body Shop TECH 08-08-2006, 11:47 AM
Replies: 1
Views: 170
Posted By FNFGTO
Help Rookie Bodyman!!!!!!

OK so I replaced the hindges on my 69 GTO because they doors were dropping a little. Now I have a clearance problem between the door and front fender (passenger side). The gap at the rear of the door...
Forum: The Body Shop TECH 08-06-2006, 09:16 PM
Replies: 3
Views: 246
Posted By FNFGTO
Help Rookie Bodyman!!!!!!!!!!!

OK So I spent the day replacing door hinges on my 69 GTO because the doors were sagging. Now I have a PROBLEM! The passenger door lines up well when closed, gaps are good, the hight is good but when...
Forum: The Body Shop TECH 07-24-2006, 01:08 PM
Replies: 3
Views: 151
Posted By FNFGTO
69 GTO window seal

I have to replace the exterior molding thats at the top of the door against the glass. How can I get the window lowered enough to get the screws out? Do I have to remove the glass?

Thanks, John
Forum: Electrical Tech 07-01-2006, 05:28 PM
Replies: 4
Views: 273
Posted By FNFGTO
What gauge replace starter cable?

I'm going to replace the wires going to the starter on my '69 GTO. After a good run I have to wait until the starter cools off before I can re start it. What gauge wire will give me the best bang for...
Forum: The Body Shop TECH 06-08-2006, 10:13 PM
Replies: 4
Views: 184
Posted By FNFGTO
Yep, there rears allright. Very different from...

Yep, there rears allright. Very different from front ones. I am sure of fit for each side as well. Aaaaaaaaahhhhhhhhhh
Forum: The Body Shop TECH 06-07-2006, 10:50 PM
Replies: 4
Views: 184
Posted By FNFGTO
Rear wheel molding 69 GTO Pics?

Finally got wheel moldings for my Goat. Front ones went on OK, look good. I can't get the rears to measure up...different shape. I contacted the previous owner, he said the rear quarters had been...
Forum: Heating & Cooling TECH 05-24-2006, 12:04 PM
Replies: 27
Views: 1,190
Posted By FNFGTO
Thermostat yes or no?

Can I get some opinions on not running a thermostat on a 69 GTO 400. No heating problems but would like to get opinions on the pros & cons.
Thanks, John
Forum: Pontiac - Street 05-15-2006, 11:50 PM
Replies: 4
Views: 328
Posted By FNFGTO
Any specs?

Any specs?
Forum: Exhaust TECH 04-05-2006, 12:01 PM
Replies: 5
Views: 465
Posted By FNFGTO
Exhaust manifold bolt removal

Exhaust manifolds leek really bad! I need to remove them but the bolts are pretty much rounded off with time. Car is a 69 GTO 4 speed. I'm not sure if I'll be putting them back on or not. I have an...
Forum: Suspension TECH 01-31-2006, 04:27 PM
Replies: 29
Views: 1,148
Posted By FNFGTO
Probably won't start until the end of the month,...

Probably won't start until the end of the month, but will check in later with an update.
Forum: Suspension TECH 01-19-2006, 10:43 AM
Replies: 29
Views: 1,148
Posted By FNFGTO
Great advice guys! I'll certainly review those...

Great advice guys! I'll certainly review those other threads. BTW I have the two different size joint forks, knew I would use them again someday.
Forum: Suspension TECH 01-18-2006, 10:19 PM
Replies: 29
Views: 1,148
Posted By FNFGTO
69 GTO Front End Rebuild

Should I try this myself or source it out? Control arm bushings are all rotted out so why not redo it all. I've heard horror stories of coil spring accidents and other problems. I am familiar with...
Forum: Exhaust TECH 03-29-2005, 05:07 PM
Replies: 3
Views: 174
Posted By FNFGTO
Have an aftermarket intake and carb on now....

Have an aftermarket intake and carb on now. Future plans include balancing bottom end, fresh pistons & rings, valve job and mild cam.
Forum: Exhaust TECH 03-29-2005, 07:06 AM
Replies: 3
Views: 174
Posted By FNFGTO
Any ideas on brand to use for 69 GTO, 400 4...

Any ideas on brand to use for 69 GTO, 400 4 speed. My current stock manifolds leak more then a Canadian submarine. I've redone my brake lines so rather not move the metering block location. I have a...
Forum: Exhaust TECH 03-29-2005, 07:06 AM
Replies: 3
Views: 174
Posted By FNFGTO
Any ideas on brand to use for 69 GTO, 400 4...

Any ideas on brand to use for 69 GTO, 400 4 speed. My current stock manifolds leak more then a Canadian submarine. I've redone my brake lines so rather not move the metering block location. I have a...
Forum: Pontiac - Street 12-15-2004, 06:39 PM
Replies: 6
Views: 124
Posted By FNFGTO
Any thoughts on Borg warner T-10 would be...

Any thoughts on Borg warner T-10 would be appreciated. I have a '69 GTO with a Muncie 4 speed that's getting a little tired, pops out of gear sometimes. I'm told the syncro's are going. You know the...
Forum: Pontiac - Street 12-15-2004, 06:39 PM
Replies: 6
Views: 124
Posted By FNFGTO
Any thoughts on Borg warner T-10 would be...

Any thoughts on Borg warner T-10 would be appreciated. I have a '69 GTO with a Muncie 4 speed that's getting a little tired, pops out of gear sometimes. I'm told the syncro's are going. You know the...
Showing results 1 to 25 of 67
Page 1 of 3 1 23

 
Forum Jump

All times are GMT -4. The time now is 07:05 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017