Forum: Pontiac - Race
04-13-2020, 12:48 PM
|
Replies: 50
Views: 8,008
|
Forum: Pontiac - Race
12-20-2019, 11:05 PM
|
Replies: 130
Views: 17,807
|
Forum: Pontiac - Race
07-07-2019, 09:34 AM
|
Replies: 51
Views: 7,861
|
Forum: Pontiac - Race
07-02-2019, 07:23 PM
|
Replies: 141
Views: 15,772
|
Forum: Pontiac - Race
03-08-2019, 04:43 PM
|
Replies: 215
Views: 32,490
|
Forum: Pontiac - Race
03-06-2019, 08:20 PM
|
Replies: 9
Views: 536
Yes, you can glue/ stack gaskets to get your...
Yes, you can glue/ stack gaskets to get your desired port alignment. I used contact cement glue and weatherstrip adhesive as well. There were times when I needed to have a thicker stack on one side. ...
|
Forum: Pontiac - Race
12-26-2018, 01:48 PM
|
Replies: 57
Views: 3,528
|
Forum: Pontiac - Race
12-25-2018, 11:02 PM
|
Replies: 57
Views: 3,528
|
Forum: Pontiac - Race
12-19-2018, 11:30 AM
|
Replies: 57
Views: 3,528
Thanks Mike,
I'm not intentionally trying to...
Thanks Mike,
I'm not intentionally trying to debate the person's or timeline involved. I'd just like knowing the full story. I had purchased my magnesium tunnel ram in early '72 from Nash. Then, I...
|
Forum: Pontiac - Race
12-18-2018, 11:38 PM
|
Replies: 57
Views: 3,528
|
Forum: Pontiac - Race
12-15-2018, 08:42 PM
|
Replies: 57
Views: 3,528
60% of your engine volume is a good place to...
60% of your engine volume is a good place to start. You'll probably end up larger, but it's easier to make spacers than it is to make stuffers. So start on the smallish side. I had that intake back...
|
Forum: Pontiac - Race
06-14-2018, 09:32 AM
|
Replies: 5
Views: 455
|
Forum: Pontiac - Race
06-14-2018, 09:23 AM
|
Replies: 29
Views: 1,440
Be sure to compare the head surface to the...
Be sure to compare the head surface to the gaskets as well. That might give you some indication as to hole size and location. Early v8 engine 50-80s holes in the heads and deck did the metering and...
|
Forum: Pontiac - Race
03-25-2018, 03:40 PM
|
Replies: 8
Views: 623
|
Forum: Pontiac - Race
02-23-2018, 11:20 PM
|
Replies: 195
Views: 8,722
You're limited by bore size/spacing plain and...
You're limited by bore size/spacing plain and simple. However you should be able to match 400 Aussie HP, because you have bigger bores. Stroking an is a shi...y way of getting cubes, because you...
|
Forum: Pontiac - Race
01-23-2018, 06:57 PM
|
Replies: 123
Views: 6,265
|
Forum: Pontiac - Race
12-30-2017, 11:17 AM
|
Replies: 73
Views: 2,947
IF, I had more money than brains, my approach...
IF, I had more money than brains, my approach would be to cast a RAV head and cast front cover to fit the larger bore spacing of the aftermarket corporate style blocks. Those blocks can be bought at...
|
Forum: Pontiac - Race
12-05-2017, 11:36 PM
|
Replies: 145
Views: 5,874
|
Forum: Pontiac - Race
11-27-2017, 09:58 AM
|
Replies: 63
Views: 3,593
Tom V., Help me here. As far as single plane...
Tom V., Help me here. As far as single plane manifolds I think the M/T was first with crossram, Offy had dual 4 inline, Nash manifold was the first single 4, then came the Edelbrock tarantula type...
|
Forum: Pontiac - Race
11-24-2017, 10:10 AM
|
Replies: 81
Views: 4,923
|
Forum: Pontiac - Race
11-24-2017, 10:00 AM
|
Replies: 30
Views: 1,812
Tapered runners with length determined by int...
Tapered runners with length determined by int closing and rpm are the way to go. Plenum volume can be tricky. Large will look good on a dyno but somewhat smaller will pull harder. Really important to...
|
Forum: Pontiac - Race
11-21-2017, 10:07 AM
|
Replies: 30
Views: 1,812
The important thing about t rams is straight...
The important thing about t rams is straight runners, less fuel being slammed into the port walls.
With fabricated t rams , they are typically built to a specific engine combo. These specifics...
|
Forum: Pontiac - Race
11-07-2017, 09:24 AM
|
Replies: 35
Views: 1,993
|
Forum: Pontiac - Race
11-02-2017, 10:12 AM
|
Replies: 14
Views: 973
I had a customer with DKM Camaro. DKM installed...
I had a customer with DKM Camaro. DKM installed Nash 5speed, 3.55 r&p, Headers and an aluminum intake on 350 engine. Custom wheels with wider255 Goodyear's and custom seat leather. It was a nicely...
|
Forum: Pontiac - Race
10-17-2017, 07:52 AM
|
Replies: 99
Views: 5,637
|