Forum: Pontiac - Street
02-26-2017, 08:37 PM
|
Replies: 44
Views: 3,508
Awhile back when I was going deep into my...
Awhile back when I was going deep into my Firebird I was pondering what OD transmission to use. I had a issue with going from a strong Th400 to something that had to be built up just to get in the...
|
Forum: Pontiac - Street
01-27-2017, 11:26 PM
|
Replies: 14
Views: 673
|
Forum: Pontiac - Street
01-26-2017, 12:15 AM
|
Replies: 16
Views: 858
I'm with Squwid; run to cooler first then to...
I'm with Squwid; run to cooler first then to radiator. Your trans fluid will run close to the water temperature, just what the trans and the fluid were designed to do. On all my vehicles I purchase...
|
Forum: Pontiac - Street
01-26-2017, 12:00 AM
|
Replies: 14
Views: 673
|
Forum: Pontiac - Street
01-25-2017, 10:11 PM
|
Replies: 14
Views: 673
Flipping a car - What would do?
I bought a project from a friend who moved out of state:
The car is a 65 Tempest with a stuck 326, ST300, and a open rear end. All numbers match.
The car has had hood, fenders, floor and trunk pans...
|
Forum: Pontiac - Street
01-24-2017, 11:35 AM
|
Replies: 13
Views: 450
Clif, thanks again for your response. I don't...
Clif, thanks again for your response. I don't want to belabor this but I don't want to make a mistake either. You said the springs work perfectly with the retainers. I believe you meant to include...
|
Forum: Pontiac - Street
01-23-2017, 10:08 PM
|
Replies: 13
Views: 450
|
Forum: Pontiac - Street
01-21-2017, 03:23 AM
|
Replies: 13
Views: 450
What retainers to use with Crower 68404 springs
Some time back a person on this form suggested I replace my stock valve springs with Crower 68404 springs because it runs out breath early.
The engine is a stock 75 400 with 5C -8 heads and a Summit...
|
Forum: Pontiac - Street
11-30-2016, 01:07 AM
|
Replies: 107
Views: 4,295
|
Forum: Pontiac - Street
02-24-2015, 12:29 AM
|
Replies: 5
Views: 557
Normally the engine sits about an inch to the...
Normally the engine sits about an inch to the passenger side. The reason for this is to make clearance for the steering box. I see you are using a rack and pinion so you may be able to center your...
|
Forum: Pontiac - Street
06-18-2014, 11:12 PM
|
Replies: 51
Views: 1,842
|
Forum: Pontiac - Street
06-18-2014, 03:21 PM
|
Replies: 5
Views: 479
|
Forum: Pontiac - Street
06-18-2014, 12:46 AM
|
Replies: 51
Views: 1,842
|
Forum: Pontiac - Street
06-18-2014, 12:41 AM
|
Replies: 5
Views: 479
|
Forum: Pontiac - Street
06-17-2014, 12:07 AM
|
Replies: 5
Views: 479
Summit Gasket Sets
The Summit web site has a lot of gasket sets ranging from from roughly $50 to $150. Do you get what you pay for? I need oil pan, timing cover, valve cover, valley, and intake gaskets. It seems an...
|
Forum: Pontiac - Street
05-31-2014, 07:47 PM
|
Replies: 37
Views: 1,395
|
Forum: Pontiac - Street
05-24-2014, 01:50 AM
|
Replies: 20
Views: 1,263
|
Forum: Pontiac - Street
05-22-2014, 03:33 AM
|
Replies: 20
Views: 1,263
|
Forum: Pontiac - Street
05-20-2014, 09:16 PM
|
Replies: 20
Views: 1,263
Yea, the engine has three holes drilled and...
Yea, the engine has three holes drilled and tapped and one undrilled boss. I think I can use the two lower drilled holes and drill the other lower boss and it will work. I don't remember if the 65's...
|
Forum: Pontiac - Street
05-18-2014, 01:48 AM
|
Replies: 20
Views: 1,263
Thanks for the responses, I brought home the...
Thanks for the responses, I brought home the engine I was planning to recam. I thought it was going to be a stock 76 Grand Prix but upon pulling a valve cover and the timing cover I can see it has...
|
Forum: Pontiac - Street
05-16-2014, 03:41 AM
|
Replies: 20
Views: 1,263
Largest cam for a 7.6:1 400
I have a 76 400 with 7.6:1 cr that I want to do a cam change. It will go in to a 65 tempest with a Th400 and eventually 3.08 gears I think they are currently taller. I have used the Summit 2800 in a...
|
Forum: Pontiac - Street
11-01-2013, 12:54 AM
|
Replies: 16
Views: 546
I'm running an early 75 block in a 69 firebird....
I'm running an early 75 block in a 69 firebird. It has five mounting holes and is not the 557 block. It is possible when the mid year change to a 577 is when they went to the two bolt motor mount....
|
Forum: Pontiac - Street
04-06-2013, 12:18 AM
|
Replies: 4
Views: 271
If you are rebuilding the transmission you may...
If you are rebuilding the transmission you may want use this opportunity to convert it to a short shaft. Had you seen the trans run before? If it worked I think you may want to clean the pan, change...
|
Forum: Pontiac - Street
04-01-2013, 10:10 PM
|
Replies: 4
Views: 273
|
Forum: Pontiac - Street
03-11-2013, 08:30 PM
|
Replies: 12
Views: 282
|