Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Showing results 1 to 10 of 10
Search took 0.00 seconds. Search: Posts Made By: deric
Forum: Pontiac - Street 09-28-2010, 08:28 PM
Replies: 177
Views: 251,857
Posted By deric
Dave's 67 GTO

Finally got the scanner fixed and the file down to a managable size. I'm more than pleased with the results of my effort to build a stout street motor. We should be able to get close to the 400hp...
Forum: Pontiac - Street 09-20-2010, 10:55 PM
Replies: 177
Views: 251,857
Posted By deric
Dave's 67 GTO

My car is finally on the road after a 5 year ground up restification. The engine was build for torq. I patterned it after an engine from Butler Performance.
69 400 Block
Eagle stroker kit from...
Forum: Pontiac - Street 01-17-2009, 06:23 PM
Replies: 3
Views: 269
Posted By deric
Flywheel pictures

I believe the one with the surface rust may be off of a 61/62 Pontiac as I have a bell housing from that era. The bell housing is cast iron and the starter bolts to the bell housing. As for the other...
Forum: Pontiac - Street 01-17-2009, 02:21 AM
Replies: 3
Views: 269
Posted By deric
Re: Flywheel Quesitions

okay I'll try and post some pictures. Will do my best to show the differences
Forum: Pontiac - Street 01-16-2009, 09:05 PM
Replies: 3
Views: 269
Posted By deric
Flywheel question

I have 3 Pontiac Flywheels all the same overall diameter. Judging buy the clutch pattern one had an 11 inch disk installed. They all have slightly different thickness 1.3, 1.34 and 1.36 inches. The...
Forum: Suspension TECH 04-13-2008, 01:29 AM
Replies: 275
Views: 150,909
Posted By deric
Torq-Thrust Original 17 x 8 with BFG's g-force KDWS's

I must have let this go too long as I can't figure out how to modify my orginial post. I have 17x8 Troq-Thrusts with 4.5" backspacing and 0" offset front and rear. I have 245/45/17s in the front and...
Forum: Suspension TECH 02-11-2008, 12:56 AM
Replies: 275
Views: 150,909
Posted By deric
Torq-Thrust Original 17 x 8 with BFG's g-force KDWS's

My 67 GTO is under construction. I have BFG's g-force KDWS's 255/50 x 17 on the rear and 245/45 x 17 up front mounted on American RacingTorq Thrust Original 17/8 4.5 BS and 0 offset. It appears...
Forum: Suspension TECH 02-11-2008, 12:19 AM
Replies: 3
Views: 248
Posted By deric
You guy's are right, after using a micrometer,...

You guy's are right, after using a micrometer, much more accurate than the mark one eye ball there isn't enough meat on the shaft to re-spline. So Now I'm thinking about 1 inch off each side.
Forum: Suspension TECH 02-10-2008, 01:19 AM
Replies: 3
Views: 248
Posted By deric
Shorting an Axle on a 67 GTO

I have a 67 GTO with a 10" non C-Clip stock rear end. I want to run 255/50x17 on American Torq Thrust orginials 17x8 with 4 1/2 " back space and 0 offest (the only way they come). With the tires and...
Forum: 66-67 GTO Tempest & LeMans TECH 12-07-2007, 12:09 AM
Replies: 14
Views: 689
Posted By deric
67 Restoration

I'm also doing a 67. I'm just a little furthur along. I would just fix what you have it's a simple fix. Then once the body is off then do the conversion. I'm assuming you'll have the frame blasted...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -4. The time now is 04:31 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017