Forum: Pontiac - Race
08-16-2017, 10:57 AM
|
Replies: 11
Views: 873
My build with an MR1 block Edelbrock heads,...
My build with an MR1 block Edelbrock heads, Scorpion rockers and an old Crane small base circle cam required 9.75 length pushrods. Manton was the only company that I could get to build me pushrods.
|
Forum: Non Pontiac Motors in Pontiacs
08-07-2017, 04:51 PM
|
Replies: 14
Views: 5,096
|
Forum: Non Pontiac Motors in Pontiacs
03-15-2017, 02:26 PM
|
Replies: 14
Views: 5,096
|
Forum: Pontiac - Street
02-24-2017, 11:28 AM
|
Replies: 27
Views: 1,087
|
Forum: Pontiac - Race
02-23-2017, 11:49 AM
|
Replies: 8
Views: 301
Water in oil
New MR1 block with edelbrock heads, found oil had been contaminated with water. Tore engine down and can not find anything wrong, head gaskets and timing chain cover gaskets are good. We have had a...
|
Forum: Pontiac - Street
02-22-2017, 11:19 AM
|
Replies: 207
Views: 7,730
|
Forum: Pontiac - Race
01-09-2017, 06:14 PM
|
Replies: 7
Views: 694
|
Forum: Non Pontiac Motors in Pontiacs
10-17-2016, 10:57 AM
|
Replies: 14
Views: 5,096
MR1-500ci going into a '76 corvette
Building my next race car and am doing something different. I bought a really junk Vette and decided it was cheaper to put it on the race track that the street. I am in the process of putting a 9"...
|
Forum: Pontiac - Race
05-27-2016, 05:39 PM
|
Replies: 6
Views: 358
|
Forum: Pontiac - Race
05-27-2016, 03:24 PM
|
Replies: 6
Views: 358
1/4 mile, yep 4:56 is stout but its what was in...
1/4 mile, yep 4:56 is stout but its what was in the car when I bought it 3 years ago. The car will be down for a few months so I will be changing to a 3:73 before it goes to the track again. I will...
|
Forum: Pontiac - Race
05-27-2016, 11:35 AM
|
Replies: 6
Views: 358
Need some advice
I am putting parts together for a new motor, and need some advice on cam and carb selection.
Engine will be a 501 built on an MR-1 block with unported High port heads.
Car will be my 1972...
|
Forum: Pontiac - Street
05-12-2016, 10:16 AM
|
Replies: 30
Views: 1,618
|
Forum: Pontiac - Race
04-29-2016, 05:01 PM
|
Replies: 7
Views: 771
|
Forum: Suspension TECH
04-26-2016, 01:34 PM
|
Replies: 4
Views: 183
|
Forum: Pontiac - Race
04-26-2016, 10:24 AM
|
Replies: 18
Views: 768
I like the name "Deputy Dog
I'm running...
I like the name "Deputy Dog
I'm running three race cars and the all have the DOG themed name. I'm from a reservation in Nebraska and my reservation name is Joseph Threedogs. So my car names are...
|
Forum: Pontiac - Race
04-25-2016, 11:22 AM
|
Replies: 18
Views: 768
|
Forum: Pontiac - Race
04-25-2016, 10:38 AM
|
Replies: 18
Views: 768
My 1962 race car
Been racing this for quite a few years and stuck in the low 13 second range. Built a new '64 389 stroker engine and first run off the trailer was a 12.46 at 107.9 mph. This is not a light weight car,...
|
Forum: Pontiac - Race
04-18-2016, 10:34 AM
|
Replies: 16
Views: 585
|
Forum: Pontiac - Street
03-25-2016, 10:35 AM
|
Replies: 25
Views: 1,012
|
Forum: Pontiac - Street
08-10-2015, 10:32 AM
|
Replies: 54
Views: 3,632
|
Forum: Pontiac - Street
08-04-2015, 10:17 AM
|
Replies: 39
Views: 1,042
|
Forum: Pontiac - Race
06-23-2015, 10:20 AM
|
Replies: 7
Views: 582
|
Forum: Pontiac - Race
06-22-2015, 05:31 PM
|
Replies: 7
Views: 582
early rods
I posted earlier asking about the strength of 1961 forged rods, well this is the answer to my own question. Rod came apart at 5400 rpm shifting from second to third. Took out the crank block and cam,...
|
Forum: Pontiac - Race
05-28-2015, 10:27 AM
|
Replies: 7
Views: 489
Lets see if I can answer all the questions that...
Lets see if I can answer all the questions that have been asked. Fuel system is a holly race pump with #8 line from tank to regulator, tank is a 5 gallon tank from jegs with a rear sump, pressure is...
|
Forum: Pontiac - Race
05-27-2015, 06:11 PM
|
Replies: 7
Views: 489
Need some advice.
428 block .030 over with BME rods DSS flat top pistons. Heads are E-heads round port with 72 chambers ported by Butlers 325 CFM flow rating. Car is a '72 Lemans station wagon with a TCI th350 trans...
|