Forum: THE LOBBY
04-23-2024, 01:01 PM
|
Replies: 13
Views: 1,456
|
Forum: Pontiac - Race
04-01-2024, 09:24 PM
|
Replies: 16
Views: 679
|
Forum: Industry Stuff
04-01-2024, 07:49 PM
|
Replies: 7
Views: 1,119
|
Forum: Members Helping Members
03-26-2024, 08:25 PM
|
Replies: 8
Views: 447
|
Forum: Pontiac - Street
03-24-2024, 10:30 PM
|
Replies: 6
Views: 412
|
Forum: Pontiac - Street
03-24-2024, 10:22 PM
|
Replies: 6
Views: 412
Thanks for the response, guys.
As I'm...
Thanks for the response, guys.
As I'm cleaning and inspecting I saw that the direct drum had 5 steels/frictions instead of 4. The pressure/backing plate has only a very small lip on the surface...
|
Forum: THE LOBBY
03-21-2024, 08:19 PM
|
Replies: 452
Views: 32,286
Did not start this today
I decided to get into this TH350 that quit a couple of years ago. Hard upshifts finally resulted in a bigger bang.
...
|
Forum: THE LOBBY
03-21-2024, 07:29 PM
|
Replies: 452
Views: 32,286
|
Forum: Pontiac - Street
03-20-2024, 11:22 PM
|
Replies: 6
Views: 412
TH350 question
I am resurrecting a TH350 that lost all the gears (except park and neutral:D).
I have it disassembled up to the center support and low/reverse clutches.
The forward and direct drums are...
|
Forum: THE LOBBY
03-18-2024, 11:19 PM
|
Replies: 29
Views: 1,279
I have not; but I have eaten eel while in New...
I have not; but I have eaten eel while in New Zealand. I think the anatomy is very similar. Among other delicacies it was cooked using geothermal steam. As I recall the flavour was mild. It was less...
|
Forum: THE LOBBY
03-14-2024, 02:05 PM
|
Replies: 18
Views: 870
|
Forum: Pontiac - Street
03-14-2024, 12:52 AM
|
Replies: 13
Views: 667
I did that. (cuz i broke one of the 8 vr from...
I did that. (cuz i broke one of the 8 vr from detonation) The l2262's were just under $400 usd. I added ARP bolts to the rods. The machine shop was another $350 CDN to swap the pistons, install the...
|
Forum: THE LOBBY
03-14-2024, 12:33 AM
|
Replies: 18
Views: 870
|
Forum: THE LOBBY
03-13-2024, 12:44 PM
|
Replies: 26
Views: 1,202
|
Forum: Pontiac - Street
03-12-2024, 07:01 PM
|
Replies: 3
Views: 271
Bad Transmission
When a trans goes bad how often would the internal structure of the trans be damaged.
I put a B&M shift kit set to street n strip in a TH350. Shifts were annoyingly harsh. Trans finally let go....
|
Forum: THE LOBBY
03-07-2024, 11:42 PM
|
Replies: 8
Views: 1,050
Has the forum changed?
"My how this forum has changed,can't even debate an issue anymore"
In response to this from another thread, I don't think it has. I have been lurking for better than ten years with a thread or a...
|
Forum: Pontiac - Street
02-26-2024, 08:52 PM
|
Replies: 15
Views: 721
I had the same problem with my 750 DP 2 corner...
I had the same problem with my 750 DP 2 corner mixture screw carb. Eyes n nose stinging n watering. Idle AFR said low to mid 10's at idle. Plugs carbon fouled. Found the transfer slots better than...
|
Forum: Pontiac - Race
02-26-2024, 04:20 PM
|
Replies: 24
Views: 1,535
Oil feed
Steve, does that mean that the figure 8 ends up looking more like an oval, or is the v groove just ground down deeper.?
|
Forum: THE LOBBY
02-26-2024, 03:53 PM
|
Replies: 20
Views: 756
|
Forum: The Body Shop TECH
02-25-2024, 05:36 PM
|
Replies: 38
Views: 1,905
|
Forum: The Body Shop TECH
02-24-2024, 10:45 PM
|
Replies: 7
Views: 516
|
Forum: The Body Shop TECH
02-24-2024, 10:40 PM
|
Replies: 7
Views: 516
|
Forum: The Body Shop TECH
02-24-2024, 01:58 PM
|
Replies: 7
Views: 516
|
Forum: The Body Shop TECH
02-23-2024, 12:41 PM
|
Replies: 7
Views: 516
Metal prep
I'm doing a small patch panel. I've had the panel for about 6 months. I used POR 15 degreaser and Por 15 metal prep to keep the bare metal panel from rusting. Should I scuff/sand the panel now or...
|
Forum: Pontiac - Street
02-11-2024, 12:13 AM
|
Replies: 16
Views: 888
|