| FAQ |
| Members List |
| Social Groups |
| Calendar |
| Search |
| Today's Posts |
|
#1
05-25-2020, 10:02 AM
|
|||
|
|||
Moser street axles A102802 8.2/8.5 10 bolt 28 spline
Anyone know if the Moser street axle can take the stock 7/16-20 wheel studs? I only see 1/2 studs in the description. Some picture I have found look like they are drilled for two seperate stud sizes.
|
|
#2
05-25-2020, 11:05 AM
|
||||
|
||||
|
This is for a single axle and shows both bolt patterns 7/16 and 1/2 in there description.https://www.moserengineering.com/a10...8-76-nova.item
|
|
#3
05-25-2020, 11:11 AM
|
|||
|
|||
|
I suck at this game thanks for finding that for me.
|
|
#4
05-25-2020, 11:35 AM
|
||||
|
||||
|
Their street axles are very hard strong steel. I have a pair of 9" 31 Spline Ford Moser Axles
that took almost 6 hours to remove 1" from each axle. (3 hrs per axle). For a F-Body 8.2/ 8.5 application, I think I would look for the 8.5" axle housing if it would fit properly under the vehicle. I have no luck with 8.2 axles surviving and decent power. Left Cap breaks. Tom V.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
|
#5
05-25-2020, 11:40 AM
|
|||
|
|||
|
I have their axles. I'm not making STUPID power, but it's pretty stout. I'm not sure if the studs are "factory", but the take a stud that has the factory bolt thread size. Unfortunately, the Wilwood kit that I have is a different thread size and lug nuts were a PITA to source that would work with the snowflakes.
__________________
77 Trans Am, 469 w/ported E-Heads via Kauffman, matched HSD intake, Butler Performance forged rotating assembly, Comp custom hyd roller, Q-jet, Art Carr 200 4R, 3.42s, 3 inch exhaust w/Doug's cutouts, D.U.I. Ignition. 7.40 in the 8th, 11.61@116.07 in the quarter...still tuning. |
|
#6
05-26-2020, 08:12 AM
|
||||
|
||||
|
I use Mosier 28 spline in my 8.5 and they have been fine for decades, and LOTS of runs in the 1.59-1.64 60' range. I pulled them once for inspection as I paint a white line on them and they haven't twisted at all.
Mine have the stock 7/16" studs in them and stock bolt pattern for the Ralley Wheels.......
__________________
If you can read this, thank a teacher. If you can read this in English, thank a Veteran! https://cliffshighperformance.com/ 73 Ventura, SOLD 455, 3740lbs, 11.30's at 120mph, 1977 Pontiac Q-jet, HO intake, HEI, 10" converter, 3.42 gears, DOT's, 7.20's at 96mph and still WAY under the roll bar rule. Best ET to date 7.18 at 97MPH (1/8th mile), |
|
#7
05-26-2020, 08:52 AM
|
||||
|
||||
|
I'm another one that uses the Moser C-clip street axle in my 12 bolt. Not only are they better steel than stock, but they are also "non" taper which makes them quite a bit stronger as well. I use stock studs in mine.
I've been running them in the Chevelle for probably the better part of 25 years now. It weighs 4,108 lbs and cuts 1.5 60 foot times. I don't even worry about the axles. |
|
#8
05-26-2020, 09:31 AM
|
|||
|
|||
|
Axles were ordered. Thanks
|
|
#9
05-26-2020, 01:34 PM
|
|||
|
|||
|
Sorry for hijacking this, but does Moser make 8.5 axles for rear disc setups for 2nd gen WS-6 TA's?
__________________
1979 Trans Am WS-6 .030 455 zero decked flat pistons 96 heads with SS valves 041 cam with Rhoads lifters 1.65 rockers RPM rods 800 Cliffs Q Jet on Holley Street Dominator ST-10 4 speed (3.42 first) w 2.73 rear gear __________________________________________________ _______________________________ 469th TFS Korat Thailand 1968-69 F-4E Muzzle 2 |
| Reply |
|
|
The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.
Linear Mode
