FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#1
|
|||
|
|||
starter info:
would you buy a power master or a robbmc performance mini starter
|
#2
|
||||
|
||||
RobbMc. good chit dere !
__________________
1981 Trans Am project -YJ 400 stroked to 488 CID-74cc Eheads-10.95:1-Northwind Intake-Holley Terminator-TH400-Moser rear-Dougs Headers.... |
#3
|
||||
|
||||
I've had a RobbMc for a few years. It starts the car reliably and I'd buy another. I had a slight issue with it right after I bought it and they fixed it and even upgraded the gear n/c while they had it. I've also used RobbMc fuel filters and highly recommend them. Great customer service.
Buy the RobbMc.
__________________
frittering and wasting the hours in an off hand way.... 1969 GTO, 455ci, 230/236 Pontiac Dude's "Butcher Special" Comp hyd roller cam with Crower HIPPO solid roller lifters, Q-jet, Edelbrock P4B-QJ, Doug's headers, ported 6X-8 (97cc) heads, TKO600, 3.73 geared Eaton Tru-Trac 8.5", hydroboost, rear disc brakes......and my greatest mechanical feat....a new heater core. |
#4
|
||||
|
||||
RobbMC. Worlds better than stock
__________________
I could explain all this to the girl at the parts store, but she'd probably call the asylum. White '67 LeMans 407/TH350/Ford 3.89... RIP Red '67 LeMans. 407/TH400/Ford 3.25 |
#5
|
||||
|
||||
I have had the power master for almost two years with no issues so far.
|
#6
|
|||
|
|||
I've got a powermaster and it works great. Just get one that's "clockable," my powermaster was not but luckily cleared the header.
|
#7
|
||||
|
||||
I have a Power Master now but if/when it goes out I'm getting a RobbMc. I have some of their other products and if their starters are of the same quality then its the one for me. Also, best customer service in the hobby.
Jim
__________________
65 Catalina sedan. Allen Thomas Performance 495. KRE Heads at 310cfm ported by SD Performance, ProSystems Dominator carb on ported Victor intake, P-Dude custom grind hydraulic roller, MSD ignition, 3.50 Moser/Ford rear. F-Glass front bumper by son Rob, rear by the old man and joint effort for trunk lid. 3950# w/driver. Best of 9.5761/139 on 175 shot, 6.01 /114 in 1/8. |
#8
|
||||
|
||||
I've had a lot of good luck with these guys:
http://www.hitorque.com/
__________________
Go Fast... Return... Go Fast Again... Who cares about left turns??? |
#9
|
|||
|
|||
If you need a shove over the edge due to the price I have two things to say.
1. Rob answers the phone him self. 2. Made in america. |
#10
|
||||
|
||||
robb all the way. the after sale support is over the top! always willing to help and replies promptly. and the starter is very good too.
|
#11
|
||||
|
||||
I have had a Power Master on my daily driven 400 TA for over 10 years.
Very dependable even for searing hot soak starts with headers. I hear RobbMc are good units.
__________________
1977 TA 400 9.5:1 CR 351hp 414LbFt, #13 Heads + 1.52 Roller rockers, 1968 Pontiac 400 intake, Holley 4165 650 DP #7054 Howards Hyd .447/.467 IN:288 EX:298 214/224@.050, MSD6A + MSD timing control + H2o/Meth 1-5/8" headers, Magnaflow 200CPI Cats + 2.5" Pypes X, Dynomax STs, TH-700R4 2200 stall, 3.42 Eaton 10-bolt, PS/PB/PW/PL/AC/Cruise 13.84@100.14mph 2.18 60' on P255-60-R15 radials, pump gas, mpg : 21.5 hwy 15.2 city |
#12
|
|||
|
|||
Robbmc.
__________________
My money talks to me-it usually says goodbye! |
Reply |
|
|