FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#21
|
||||
|
||||
You’ll be borderline on the street. Upgrade if you hit the track. My old 470 ish hp 455 did well on the street. At the track, it would pop through the air cleaner just before the line at the top end. Pulled the plugs. All white like a bed sheet.
|
#22
|
||||
|
||||
Quote:
Pressure is one thing, volume is another, I'm sure you're aware. Whether it matters or not, when I'm doing a moderately high HP EFI build, I just run the 1/2" lines to and from and be done with it. One reason is because I'm typically replacing fuel lines on a build anyway, so I just upgrade to 1/2", the cost is the same. Ironically both of our current EFI cars (one running 10's and the other 11's) already had 1/2" lines and in tank pumps when they had carbs, so all of that was left in place when the switch to EFI was made. |
The Following 2 Users Say Thank You to Formulajones For This Useful Post: | ||
#23
|
||||
|
||||
Quote:
|
The Following User Says Thank You to Skippy597 For This Useful Post: | ||
#24
|
|||
|
|||
Quote:
Sent from my SM-S901U using Tapatalk |
#25
|
||||
|
||||
Quote:
What fuel setup do you have on that pretty light blue TA of yours?
__________________
1977 Black Trans Am 180 HP Auto, essentially base model T/A. I'm the original owner, purchased May 7, 1977. Shut it off Shut it off Buddy, I just shut your Prius down... |
#26
|
||||
|
||||
Send Caster1 a DM and ask him about his setup, it has a 1/2 pickup and a few other mods. Its pretty sick.
__________________
468/TKO600 Ford thru bolt equipped 64 Tempest Custom. Custom Nocturne Blue with black interior. |
#27
|
||||
|
||||
That's the car I was talking about. I always wanted that car to look "stock". For years I ran two Holley blue pumps. One through the factory 3/8 line for the nitrous and one for the motor side. I added a peice of .500 tubing that entered the front of the tank but ran to the rear. That set up worked well when the car ran bottom 11's and low tens on spray. When we upped the power it became inconsistant and the pressure gauge moved around more than I liked. No matter what I tried I couldn't get it to work to my satisfaction so I ended up installing a new tank with a sump.... Now I need to build another car to use the old tank
|
#28
|
||||
|
||||
Pretty simple to make them look stock with a little thought and time.
I use the Tanks Inc tanks with the pump in the tank. No sumps hanging down. I run the 1/2" line, sometimes using stainless pre bent stuff from places like Inline or Right Stuff, which gives the appearance of stock if anyone cared to crawl under the car. I then keep the stock mechanical pump in place if it's visible (like a Chevrolet) and keep the stock steel lines running to the carb or EFI, although it's all dummy stuff with the line soldered shut. The 1/2" line I hide in the back where it can't be seen. Look under the car or open the hood and it looks like a typical street car with a mechanical pump but it actually has a fuel system that'll support 1000+ HP depending on which pump I put in the tank |
#29
|
||||
|
||||
Quote:
|
#30
|
||||
|
||||
Quote:
They make it so easy these days with these fuel systems, it's like modern car stuff. Problem is.....none of it's cheap. |
#31
|
||||
|
||||
Ok so I got a robbmc 1/2" pickup and inline tube 1/2" fuel line on the way. Now my question is do I need to get a 1/2" carb feed line from the pump or will the robbmc pump supply suffecient pressure with a 3/8" line.
|
The Following User Says Thank You to Skippy597 For This Useful Post: | ||
#32
|
||||
|
||||
Ive done 3/8 from the pump to carb or the regulator to carb to make things look stock and works fine. 1/2" is always better but the most important thing with a mechanical pump is having the larger feed line on the suction side because they aren't good at sucking, that's a long distance and making it as easy as you can on the pump with larger line helps that scenario.
|
#33
|
|||
|
|||
Agreed the bigger pump to carb line isnt always required, but, if you have a Q-jet & dont care about an original looking/size line, using a 1/2" or -8 AN line will provide a little more fuel from pump to carb if that matters. Its easy to run a -8 line from the robbmc pump outlet to the carb using one of cliffs -8 AN fitting & high flow marine filter.
|
#34
|
||||
|
||||
Quote:
|
#35
|
|||
|
|||
I have an older version of the robbmc 1100 pump, not sure if the inlet/outlets are the same as newer models or the 550, but I used a summit or fragola brand curved 90 AN fitting on the outlet then ran the -8 braided hose up behind the p/s pump & alternator basically where the stock metal 3/8 line runs, -8 line is about 1/2" OD so its a lot bigger than 3/8 line, it slides through that area easily and is nowhere near moving parts or belts, its rigid ennough that it stays in place... i even added a small regulator to it that sits near the T-stat housing freely suspended with no bracket. i can get some pics of how its routed but its really pretty basic.
Dont forget the robbmc pump is clockable so you can adjust where the inlet/outlets are somewhat. |
The Following User Says Thank You to 78w72 For This Useful Post: | ||
#36
|
||||
|
||||
Thank you 78w72, pictures not needed, I see that a 1/2" OD line will fit through there fine and it sounds like it will be able to take the slight curves necessary to hook up and not kink or anything like that. Do you have an in-line filter along with the regulator too? I've usually used in-lines as it seems the in-housing filters (short/long) are so small but I see that Cliff sells pleated filters so they must be able to do the job. It would be a cleaner instl without.
The clockability is a cool feature. I'm really impressed with the quality and heft of the unit. Just an FYI, the pump I took out had the outlet (bottom) on the same side of the pump as the inlet (1969 428) and I also looked at the pump on the 1969 400 in my other car and the outlet is on the opposite side of the pump. I would not claim either configuration is original or correct or whatever but the lines for both go up between timing chain cover/pump bracket/head. thank you for your help |
#37
|
|||
|
|||
Quote:
I have filters, one bigger tanksinc right after the tank then just use the marine screen type right before the carb, cliffs AN fitting uses the high flow marine screen type, im sure you can use the factory pleated paper type too but the marine filter is supposed to flow better. I have checked both filters a couple times after years of use and the carb one is always spotless and so is the bigger one but it has a brass element so harder to see if there are any small specs in it, looks totally clean to me, i do have a new tank so no debris to get churned up. I dont have or feel the need for any other inline filters. Heres a pic just to show the carb AN fitting & how the line is ran, i have since shortened the line a bit & now run a regulator for when I want to dial the 1100 pump up to a higher psi for track use but a regulator shouldnt be needed for most carbs with the 550 pump since its set at ~7psi. |
The Following User Says Thank You to 78w72 For This Useful Post: | ||
#38
|
||||
|
||||
I've done 1/2" steel line from pump to carb on some installs. It fits and works. Just a little tedious and time consuming but it all is really.
|
The Following User Says Thank You to Formulajones For This Useful Post: | ||
#39
|
||||
|
||||
Thank you 78w72 and Formulajones. My plan is in place and putting the parts list together.
|
Reply |
|
|