[cgeise]

Time to clean stuff out -- FOR SALE

Water cross-overs -$50 each (2)
Manley Valve springs 221425 used but good $100, one set with ti retainer's $200
Comp cams 948 Springs $75
Edelbrock stud girdle $75
Billet roller cams
(1) turbo grind - $250
(1) new ultra Dyne 280/283 -- $275
(1) used, nice 284/290 -- $200
(1) used 50 mm 282/292 --$250
Moldex billet crank - std, std - $1750
Accusump with electronic control valve and 25lb switch $200
One set EFI fuel rails -- edelbrock - $50
Tiger intake -- Flange cut .750 down with turtle $250
Tci Damper - the "Rattler" $ 150
Crower roller lifters - 14 extreme duty tall, offset lifters with pin oiler--$150
One set Ross pistons for Tiger heads for 4.350 bore with pins --$250
One set Diamond Pistons for tiger heads, side coated for 4.375 bore with pins -- $350
One set Smith bro push rods 3/8 buy 165 wall (8) 9.00 long and (8) 9.050 long $75

[mgarblik]

Please tell me more about the Moldex crankshaft. 3.25 or 3" ? Standard Pontiac or BBC rods std. Balanced? and if it is any idea of the bob weight? I assume it has been run. Any run history? Does it have a standard Pontiac long keyway or 2 short ones? With or without 1/4 keyways for a blower hub? I guess yiou can tell I am interested. Most important to me, what is the stroke? Thanks for the info.

[Kevspontiacs@aol.com]

curt can I get the specs on the turbo cam?

[Jim Zeek]

pic of accusump please

[aaronman]

Curt - PM me the details of the 50mm cam. I could use a back up if the lobe lift, LSA and duration at .050 are close to my current stuff. Thanks.

[pontsd]

Pm sent

[Aaron Quinton]

Curt,

What are the main and rod diameters on the crank you have for sale?

Thanks,

Aaron

[cgeise]

Crank is a 4.5 in stroke 3 in main with bbc rods-- repaired after one rod scuffed it was magged and re-heat treated after repair back to std size - it would have been fine at 10 or 20 under, but I didn't want that. Standard single keyway and when last used it was balanced with Oliver steel rods.

[mgarblik]

I'm locked into a 4.25 stroke, damn.

[aaronman]

Curt - I'll take the 50mm cam. Check your pm. Thanks!

[cgeise]

Sorry for the screw up -- but the cam listed as 50mm is really a 55mm -

[69camarox]

is the tiger intake ported if so what size is it at the intake gasket

[JD]

Interested in the crank, intake and pistons if they are still available. Sent you a PM with some questions.

[Donovan]

Hey Curt...

Which FI rails are you selling? victor or super victor?

[RA462]

What is the lobe lift is on that 55mm cam? LSA?

[cgeise]

Originally Posted by Donovan

Hey Curt...

Which FI rails are you selling? victor or super victor?

Rails were on the " big" Victor - race Manifold

[cgeise]

Originally Posted by RA462

What is the lobe lift is on that 55mm cam? LSA?

Ill get it later today for you.

[66sprint]

Curt
If the EFI rails are not already spoken for, and if they are Edelbrock #3634 and new, I will take them.
I will send PM too.
Chris

[Donovan]

Originally Posted by cgeise

Rails were on the " big" Victor - race Manifold

I'm interested. May I have a few pics?

[cgeise]

Originally Posted by Donovan

I'm interested. May I have a few pics?

There like new fuel rails - -Pics really ?? Not trying to be a jerk here but --