#1  
Old 12-18-2019, 11:19 PM
694.1 694.1 is offline
Ultimate Warrior
 
Join Date: Jul 2010
Location: SE WI
Posts: 1,366
Default Steel crank to stoke the early blocks?

How practical would it be to turn down one of the modern steel cranks to fit the small journal blocks? You could make a 389+ out of a 370, stroke a 347 at least 20 cubes too.
The 287 & 316 ports are just too small get very serious with, unless you were to use 370-389 heads & manifolds.
Sure, you could just use a 59-60 389 block & crank but that would be way to simple. Unless you were building a 421.
Curious about the potential here.
And would you recommend a morse chain??

__________________
"At no time did we exceed 175 mph.”
Dan Gurney's truthful response to his and Brock Yate's winning of the first ever Cannonball Baker Sea-to-Shining Sea...

Still have my 1st Firebird
7th Firebird
57 Starchief
  #2  
Old 12-18-2019, 11:32 PM
tom s tom s is offline
Ultimate Warrior
 
Join Date: Jan 2000
Location: long beach ca usa
Posts: 18,764
Default

Not sure what your really trying to do but it's all just numbers in a check book.i have done a lot of strange builds but have never tried to go back to older blocks.I have done 2 short deck RA Vs with cut down and offset ground 57-58 cranks.Tom

  #3  
Old 12-18-2019, 11:37 PM
tom s tom s is offline
Ultimate Warrior
 
Join Date: Jan 2000
Location: long beach ca usa
Posts: 18,764
Default

If you have to use a 57-58 block you could buy a 3in main 4-4.21-4.25 stroke crank and just have the mains turned down and not having to offset grind.Tom

  #4  
Old 01-23-2020, 11:27 AM
Rocky 389's Avatar
Rocky 389 Rocky 389 is offline
Senior Chief
 
Join Date: Feb 2004
Location: Bellevue, Nebraska
Posts: 310
Default

......and you don't need to restrict yourself to early heads if you don't want to. I've got late heads on my old 347 punched .125 to 370. Still using reverse cooling. Not a lot to it.
Advantages are larger ports/valves, screw-in studs [I used big block 7/16ths chevy studs] and pushrod guide plates. Down side is lots of CCs. I think my 73 GTO heads are 98 CCs so to get decent compression I used Jahns pistons with a nice "lump" on them. Rockers oil up through the pushrods.

__________________
Roll around in the excitement
  #5  
Old 01-23-2020, 08:22 PM
694.1 694.1 is offline
Ultimate Warrior
 
Join Date: Jul 2010
Location: SE WI
Posts: 1,366
Default

Later heads sound like an appealing option, though I would top off such a beast with a 65-67 AFB intake or a TP intake.
A Q jet would just look wrong in the application, kinda like a "Caitlyn" Jenner sort of deal!
Has anyone ever figured out how late a head casting would take an early gusher tube? It seems very unlikely that the '65+ heads would -when the heads were revised,
it would make no sense compromise the design for obsolete technology.
Ah, so many engines, so little time!

__________________
"At no time did we exceed 175 mph.”
Dan Gurney's truthful response to his and Brock Yate's winning of the first ever Cannonball Baker Sea-to-Shining Sea...

Still have my 1st Firebird
7th Firebird
57 Starchief
  #6  
Old 01-24-2020, 02:41 AM
Jack Gifford's Avatar
Jack Gifford Jack Gifford is offline
formerly 'Pontiac Jack'
 
Join Date: Dec 2004
Location: Phelps, NY 14532
Posts: 10,176
Default

Original gusher tubes do not fit in later heads. But that doesn't prevent building a reverse-flow-cooled engine with later heads. Pontiac's reason for the tubes was to cool the exhaust seats enough to get away without seat inserts.

__________________
Anybody else on this planet campaign a M/T hemi Pontiac for eleven seasons?
... or has built a record breaking DOHC hemi four cylinder Pontiac?
... or has driven a couple laps of Nuerburgring with Tri-Power Pontiac power?(back in 1967)
  #7  
Old 01-24-2020, 10:55 AM
Murf Murf is offline
Ultimate Warrior
 
Join Date: Aug 2000
Location: St. Marys Ks. U.S.A.
Posts: 1,486
Default

Hey, I don’t want to derail this thread but I have a question.

Is it possible to run a later block & heads and use the old style water pump?

You would have to use the early front cover, right? It has a different style seal & uses a slinger type thing. Doesn’t it?

I’m thinking of something similar to what Rocky has done. A Hot Rod with the cool looking old pump set up. What would be the best way to do this and end up with a block mounted starter & maybe side motor mounts?

Thanks
Murf


Sent from my iPhone using Tapatalk Pro

  #8  
Old 01-24-2020, 11:56 AM
Bill Hanlon's Avatar
Bill Hanlon Bill Hanlon is offline
Ultimate Warrior
 
Join Date: Feb 2005
Location: Fredericksburg, TX
Posts: 2,349
Default

I'm not saying you can or can't use an early timing cover on a later block, but if you want to get rid of the "slinger type thing" check out these instructions I wrote into a "how to".

http://www.pontiacsafari.com/L1Garag...ealUpgrade.pdf

__________________
My Pontiac is a '57 GMC with its original 347" Pontiac V8 and dual-range Hydra-Matic.
  #9  
Old 01-24-2020, 12:34 PM
Murf Murf is offline
Ultimate Warrior
 
Join Date: Aug 2000
Location: St. Marys Ks. U.S.A.
Posts: 1,486
Default

Quote:
Originally Posted by Bill Hanlon View Post
I'm not saying you can or can't use an early timing cover on a later block, but if you want to get rid of the "slinger type thing" check out these instructions I wrote into a "how to".

http://www.pontiacsafari.com/L1Garag...ealUpgrade.pdf


Thanks for the quick reply, Bill! I’m limited to Tapatalk right now so I can’t see your link for some reason. I will check it out later this evening. I just want to let you know I appreciate the response.

Murf


Sent from my iPhone using Tapatalk Pro

  #10  
Old 01-24-2020, 12:58 PM
tom s tom s is offline
Ultimate Warrior
 
Join Date: Jan 2000
Location: long beach ca usa
Posts: 18,764
Default

JMHO,I would use the first year alu timing cover which I think is 1961 with the newer seal in it and the 4 bolt pump.I have used them on late blocks with no issues.Tom

  #11  
Old 01-25-2020, 12:23 AM
Murf Murf is offline
Ultimate Warrior
 
Join Date: Aug 2000
Location: St. Marys Ks. U.S.A.
Posts: 1,486
Default

Quote:
Originally Posted by tom s View Post
JMHO,I would use the first year alu timing cover which I think is 1961 with the newer seal in it and the 4 bolt pump.I have used them on late blocks with no issues.Tom


Thanks Tom! I’ll have to look into that. Sounds like a pretty easy way to do it. I don’t know how hard it would be to find a timing cover though.

Thanks again
Murf


Sent from my iPhone using Tapatalk Pro

  #12  
Old 01-25-2020, 10:58 AM
tom s tom s is offline
Ultimate Warrior
 
Join Date: Jan 2000
Location: long beach ca usa
Posts: 18,764
Default

They are around,just a little harder to find a really good one.There was one on ebay a few days ago.Just do a search for 1961,1962 and 1963 timing covers.Late 63 will be a 8 bolt water pump.Tom

  #13  
Old 01-25-2020, 11:00 AM
tom s tom s is offline
Ultimate Warrior
 
Join Date: Jan 2000
Location: long beach ca usa
Posts: 18,764
Default

here you go
https://www.ebay.com/itm/PONTIAC-61-...YAAOSwypZb1m7Q

  #14  
Old 01-25-2020, 12:37 PM
Murf Murf is offline
Ultimate Warrior
 
Join Date: Aug 2000
Location: St. Marys Ks. U.S.A.
Posts: 1,486
Default

Quote:
Originally Posted by tom s View Post


Thanks Tom


Sent from my iPhone using Tapatalk Pro

  #15  
Old 02-01-2020, 02:59 AM
Rocky 389's Avatar
Rocky 389 Rocky 389 is offline
Senior Chief
 
Join Date: Feb 2004
Location: Bellevue, Nebraska
Posts: 310
Default

I used the original 1957 timing cover/water pump and had my machinist open the snout hole to take a modern press-in, lip-type seal. If you want to the the 55-59 reverse cooling elbows at the front of the modern heads you'll find the heads are 1/4" shorter that the originals. This is a good thing because it gives you the opportunity to make up a pair of 1/4" spacers for the elbows. After you pop the front frost plugs out of your modern heads, you'll see the elbows line up with the mount holes in the heads but the coolant hole in the elbows is now offset from the cooling holes in the heads. This is where those 1/4 thick adapters come in. I used my "Christmas tree" carbide cutter in my die grinder to "blend" and manipulate those coolant holes to line up better although the coolant has to flow through the dog-leg.
The coolant passages in the newer heads appear to be pretty small but I've had no cooling problems with mine. Coming up on 3 years since I put it together and my car is not babied or trailered probably have 6-7000 miles on the engine now.
Attached Thumbnails
Click image for larger version

Name:	370waternecks.jpg
Views:	196
Size:	58.4 KB
ID:	530729  

__________________
Roll around in the excitement
  #16  
Old 02-01-2020, 07:03 PM
Murf Murf is offline
Ultimate Warrior
 
Join Date: Aug 2000
Location: St. Marys Ks. U.S.A.
Posts: 1,486
Default

Quote:
Originally Posted by Rocky 389 View Post
I used the original 1957 timing cover/water pump and had my machinist open the snout hole to take a modern press-in, lip-type seal. If you want to the the 55-59 reverse cooling elbows at the front of the modern heads you'll find the heads are 1/4" shorter that the originals. This is a good thing because it gives you the opportunity to make up a pair of 1/4" spacers for the elbows. After you pop the front frost plugs out of your modern heads, you'll see the elbows line up with the mount holes in the heads but the coolant hole in the elbows is now offset from the cooling holes in the heads. This is where those 1/4 thick adapters come in. I used my "Christmas tree" carbide cutter in my die grinder to "blend" and manipulate those coolant holes to line up better although the coolant has to flow through the dog-leg.

The coolant passages in the newer heads appear to be pretty small but I've had no cooling problems with mine. Coming up on 3 years since I put it together and my car is not babied or trailered probably have 6-7000 miles on the engine now.


Thanks for the info Rocky! I’d love to see your car sometime.

Thanks again
Murf


Sent from my iPhone using Tapatalk Pro

  #17  
Old 02-13-2020, 11:50 AM
Rocky 389's Avatar
Rocky 389 Rocky 389 is offline
Senior Chief
 
Join Date: Feb 2004
Location: Bellevue, Nebraska
Posts: 310
Default

Come to the HAMB drags. I'll be there with the car.
Attached Thumbnails
Click image for larger version

Name:	34DRAGS19.jpg
Views:	157
Size:	71.1 KB
ID:	531806  

__________________
Roll around in the excitement
  #18  
Old 02-13-2020, 01:14 PM
Murf Murf is offline
Ultimate Warrior
 
Join Date: Aug 2000
Location: St. Marys Ks. U.S.A.
Posts: 1,486
Default Steel crank to stoke the early blocks?

Quote:
Originally Posted by Rocky 389 View Post
Come to the HAMB drags. I'll be there with the car.


I’ll have to look into that. Are the HAMB drags held at MoKan? Do you go to any local stuff? Your in Nebraska aren’t you? I live close to Topeka Ks so wouldn’t be much of a drive, if there was a show or cruise you’d be at.

Thanks again for all the info!
Murf


Sent from my iPhone using Tapatalk Pro

  #19  
Old 02-16-2020, 05:02 PM
Rocky 389's Avatar
Rocky 389 Rocky 389 is offline
Senior Chief
 
Join Date: Feb 2004
Location: Bellevue, Nebraska
Posts: 310
Default

HAMB drags are at MoKan. I''m in the Omaha area and I've been known to frequent all the local cruise nights.

__________________
Roll around in the excitement
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:13 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017