[Stan Weiss]

I have been ask for another list. With the only requirements being the engine has to have used PMD head casting, and PMD block casting.

So post up your combinations.

Thanks
Stan

[Jack Ferris]

Going back to the early 90's here. 3200# 69 GTO 455 (469) untouched 614 heads 276-280 .440 Comp roller, Warrior intake, 9375 Holley. Would run 10.90-11.00's at our 4250' track.

[Stan Weiss]

Originally Posted by Jack Ferris

Going back to the early 90's here. 3200# 69 GTO 455 (469) untouched 614 heads 276-280 .440 Comp roller, Warrior intake, 9375 Holley. Would run 10.90-11.00's at our 4250' track.

Jack,
Do you happen to remember the MPH?

Thanks,
Stan

[Gary H]

Had a 84' Trans Am tube chassis car back in 1987. Pretty light, 2400 lbs. Ran a 455 block, factory 455 crank, hand ported RA IV heads, Warrior intake. Best time was a 9.30 at 139 mph

[Jack Ferris]

Stan- 122-124 for the mph

[Stan Weiss]

Originally Posted by Gary H

Had a 84' Trans Am tube chassis car back in 1987. Pretty light, 2400 lbs. Ran a 455 block, factory 455 crank, hand ported RA IV heads, Warrior intake. Best time was a 9.30 at 139 mph

Gary,
Is 2400# with driver?

Thanks
Stan

[Stan Weiss]

Originally Posted by Jack Ferris

Stan- 122-124 for the mph

Jack,
Thanks

Stan

[Bill Eveland]

I bought a combo from 9secdport on here years ago. 59 cc 62s, 280/284 sr .440 lobe ,victor, 1050 dominator. 3300 lbs, he went 9.60 140mph . 15:1 462.

[Steve C.]

1970 Trans Am
10.68 at 125 mph

'70 400 block / 462 CID
4.182" bore
4.210" stroke ( factory crank w/ mains cut to 3")
6.625" rods
1969 #16 d-ports
12.49:1 compression
Ultradyne solid roller
264/ 271 @ .050"
.4176" lobe lift / 1.65 rocker ratio
108 LSA
Victor intake / Brad Urban Stage III 750 Holley
1-7/8" headers

626 hp @ 6400 rpm on a generous dyno

TH400/ 8" converter/ 4.33 gear
28-10.5-15w M/T slicks
Race weight about 3620 lbs.

.

[Scott Stoneburg]

474 cu.in. D-Port #62 - 12.75 to 1 , Victor manifold, 1050 Dominator, Lunati SR 268/275@ .050, W/ .604 lift. cam. , 1-78" to 2" step headers. , 3" exhaust over the rear axle. 3550LB race weight 1967 Firebird
10.55 @ 129 mph

[Stan Weiss]

Originally Posted by Bill Eveland

I bought a combo from 9secdport on here years ago. 59 cc 62s, 280/284 sr .440 lobe ,victor, 1050 dominator. 3300 lbs, he went 9.60 140mph . 15:1 462.

Bill,
Thank You. Did you ever run the motor?

Heads and Block List.
http://www.magneticlynx.com/carfor/pont_pmd.htm

Stan

PS I will add these other later tonight.

[opeliac]

1969 Lemans weighing 3680lbs in the early 90s...455 with 191 heads, 3680lbs, working A/C, 4.10 gears and 10" tires...6.66 in the 1/8th, 10.20s in the 1/4.

[Bill Eveland]

Stan I ran the heads and rest of top end, but without domed pistons and aluminum rods that he ran. I was shifting way before him as well. and only 13:1. I was 10.54ish at 125 at 3500 lbs with a 3.73 and 28" tire.

[Stan Weiss]

Thanks everyone.

Stan

[tom s]

There are a few guys that are not on the net I will try to contact.Nunzi,Ric Johnson,Bill Blair for a couple.Will also see what Dave Johnson ran.Before Wenzlers.Blair and Nunzi only ran factory stuff.All 4 ran 980 heads with factory blocks.Tom

[tom s]

Also Brother Leak,Stienbeck,and the Nor Cal guy who's name I can't remember ran RA V Astras with stock blocks.Tom

[Richie Hoffman]

68 firebird 3000 lbs 455 ram air 4 heads hyd flat tappet cam 1050 carb wenzler intake went 9.99 @132 in 1995

[ScottK.]

Just curious does this list include boost?

[tom s]

Rudy Diphous(spelling) was the other Astra racer.A board member I believe owns his car.Tom

[Stan Weiss]

Originally Posted by Richie Hoffman

68 firebird 3000 lbs 455 ram air 4 heads hyd flat tappet cam 1050 carb wenzler intake went 9.99 @132 in 1995

Richie,
Thank you the information has been added.

PMD Heads and Block List.
http://www.magneticlynx.com/carfor/pont_pmd.htm

Stan