[adam woodmancy]

472Pontiac 4.205x4.25
Just bored,honed,and decked. All new coated Clevite Bearings,
new freeze plugs.
New ARP main studs.
Factory main caps.
New Canton 7 qt pan and pickup.
New Melling 80# oil pump and hardened oil pump shaft. B.O.P. engineering Viton rear main seal and one piece pan gasket.
Brand new cast timing chain cover from Jim Butler Performance.
New cast oil filter housing from Jim Butler Performance. New Eagle 4.25 stroker crank New Eagle 6.8 H Beam rods New Ross Flat top pistons. New Total Seal rings. Filed and gapped for up to 150 shot of N2O
Billet Double Roller Timing chain and gear.
Assembly is fully balanced
Lunati Solid Street Roller Cam # RRC-248-555 which is .248/.555 lift with 1.5 rockers, .590 lift with 1.65 with 112 lobe separation.
B.O.P. engineering Aluminum Valley Pan with PVC provision New Meziere Electric Water Pump
Block is not filled.
Have over 5 k parts and labor in shortblock.
Shortblock assembled
$3,500 obo




SD performance 340/350 cnc 87 cc heads. 2.20/1.74 valves with titanium retainers set up for solid roller
SD cnc northwind intake for heads. 4150 flange
850 holley d.p. carb
Heads and intake are brand new, and cost over $3700

$3,500 for heads, intake, carb







$6,000 for all.
Shortblock, heads, intake and carb.
Located in central ,IL

Will not separate heads and intake.

Expecting to make 600 hp on pump gas with this engine.

also have a set of brand new hedman husler round port headers for 68-72 a body
Coated , over $700 new, asking $500.

RACERMX38@HOTMAIL.COM
or
309-241-3497

Thank you. Adam

[Brent Flynn]

man...i wish i had 6000.00! This would look REAL good in my '72 Lemans Wagon
I was lookin forward to seeing how fast your car was gonna go!

[69camarox]

would this head work with a 4.155 bore seemes like a large intake valve

[adam woodmancy]

Originally Posted by Brent Flynn

man...i wish i had 6000.00! This would look REAL good in my '72 Lemans Wagon
I was lookin forward to seeing how fast your car was gonna go!

I know brett, I really don't want to sell it. I got some other things up for sale too, so if they go, I won't be in such a bind... Hopefully things will work themselves out and I can keep it, but if not, its back to the old slow 400 for a while. It sucks to be so close.. all I need to finish it is lifters and pushrods

[adam woodmancy]

Originally Posted by 69camarox

would this head work with a 4.155 bore seemes like a large intake valve

. Honestly, I'm not sure. Dave as SD performance would be the man to ask. I just know that is the standard size valves for that package on a stock block. If you have and aftermarket block, the intake valve jumps to 2.24 I believe.

[FT LB]

Just left message. Gonna PM... Thanks. Tim

[BLANK1]

Don't do it. I was in a bind a few years ago and sold my 463 and regretted it ever since. Put my old stock 400 back in my car. Went from low 11's back to 13's. It's taken me over 2 years now just to get a new motor built and finally I should have it in this year. Building a 600 hp 461. Wish I had heads like yours but I have to settle for mildly ported E-heads. Well, I hope it will make 600 hp.

[Hooter]

Originally Posted by 69camarox

would this head work with a 4.155 bore seemes like a large intake valve

I've got a set of sd e heads on my 4.18 bore motor with 2.19 intake valve.

[adam woodmancy]

Sale pending on heads,intake and carb.

[adam woodmancy]

New price on short block. $3,000 firm

$400 for hedman headers

[GTO Dan]

Hi Adam,

I left you a voicemail on the headers. Thanks

[adam woodmancy]

Dan, just got your message. I will try to call you between 12-1 central time on my lunch hour. Thank you. - Adam

[David Jones]

"Filed and gapped for up to 150 shot of N2O"

Can you fill me in on what that means?

Forged crank?

I'm looking for a 455 shortblock to bolt my set of lightly ported 6X heads to. Yours is more cam than I want though.

[adam woodmancy]

They just have a little more gap than a standard ring set to allow for the added cylinder pressure of nitrous. It is NOT a forged crank, just a standard cast eagle crank. Hope this helps, thanks for looking

[Frogday]

This might be what I need to replace the one I just cracked...sent e-mail with some questions.

Thanks,
Bryan

[adam woodmancy]

Sale pending on shortblock, headers still available. Thanks for looking

[adam woodmancy]

Bump.

Shortblock still available... $3000

Hedman round port coated headers for 68-72 abody $450

[adam woodmancy]

Bump

[adam woodmancy]

Bump

[adam woodmancy]

$2500 for the shortblock.

This is a steal guys. Yes its a cast crank, no its not one of the better blocks. It will never be a high hp , high rpm screamer, but if you have a street / strip car and you want a nice torquey stroker motor, you can't get one like this for this price.. read the ad, look at the peices and do the math. I will not ship.