#1  
Old 01-19-2020, 03:01 PM
footjoy's Avatar
footjoy footjoy is offline
Chief Ponti-yacker
 
Join Date: Oct 2009
Location: KC
Posts: 977
Default When do big valve heads out perform small valve heads?

I know the large valve heads rule. If you have two identical castings one with the big valves and one with small valves, at what point do the big valve heads make more horsepower is it at 1000 rpm or 2000, or 4500? I am just curious. if it is 3500 or more how much would a everyday cruiser benefit?

Thanks

  #2  
Old 01-19-2020, 03:35 PM
slowbird's Avatar
slowbird slowbird is offline
Ultimate Warrior
 
Join Date: Jan 2001
Location: Montgomery, IL
Posts: 10,638
Default

Just my opinion but everywhere everytime if setup up right

  #3  
Old 01-19-2020, 04:38 PM
67gtospud's Avatar
67gtospud 67gtospud is offline
Ultimate Warrior
 
Join Date: Aug 2012
Location: Seymour, Wisconsin
Posts: 1,549
Default

There’s a lot of variables but, theoretically if you put the same heads on the same engine with the only difference being one has big valves vs small valves, the big valve head should outperform throughout the entire rpm range since more air can be moved than the small valve heads.

__________________
1967 GTO, 432 (428+.030), 4-bolt mains, factory Nodular crank, scat rods, icon dished pistons, Lunati HR 243/251@.050, .618/.622 lift, Edelbrock 72cc round port heads, 10.5:1, offy 2-4 intake, Edelbrock 650cfm carbs, Super T10 trans (2.64 first), BOP 10 bolt w/ Eaton posi and 3.36 gears
  #4  
Old 01-19-2020, 05:04 PM
footjoy's Avatar
footjoy footjoy is offline
Chief Ponti-yacker
 
Join Date: Oct 2009
Location: KC
Posts: 977
Default

Quote:
Originally Posted by 67gtospud View Post
There’s a lot of variables but, theoretically if you put the same heads on the same engine with the only difference being one has big valves vs small valves, the big valve head should outperform throughout the entire rpm range since more air can be moved than the small valve heads.
Ok that was probably a stupid question.

Thanks

  #5  
Old 01-19-2020, 05:15 PM
Scott Roberts Scott Roberts is offline
Suspended
 
Join Date: Oct 2006
Posts: 3,181
Default

Quote:
Originally Posted by footjoy View Post
Ok that was probably a stupid question.

Thanks
Not really.. a small valve can be torquey in the lower rpm. The smaller valve can produce higher velocities in that range in general terms so youre question itself isn't stupid

  #6  
Old 01-19-2020, 05:20 PM
b-man's Avatar
b-man b-man is offline
Moderator
 
Join Date: Sep 2002
Location: Sunny So Cal
Posts: 16,410
Default

Moved to Street forum, the engine in question is for a street cruiser.

I honestly doubt you’d see any difference between the big and small valve heads on your Tri-Power street 400 with the 068 or similar cam you’re planning on using.

Keep in mind that all Tri-Power engines had small valve heads and none of them were slouches.

__________________
1964 Tempest Coupe LS3/4L70E/3.42
1964 Le Mans Convertible 421 HO/TH350/2.56
2002 WS6 Convertible LS1/4L60E/3.23
  #7  
Old 01-19-2020, 06:15 PM
Steve C. Steve C. is offline
Ultimate Warrior
 
Join Date: Dec 1999
Location: Liberty Hill, Tx. (Austin)
Posts: 10,385
Default

http://www.wallaceracing.com/hp-valve-size.php

http://www.wallaceracing.com/intake_valve.php


.

__________________
'70 TA / 505 cid / same engine but revised ( previous best 10.63 at 127.05 )
Old information here:
http://www.hotrod.com/articles/0712p...tiac-trans-am/

Sponsor of the world's fastest Pontiac powered Ford Fairmont (engine)
5.14 at 140 mph (1/8 mile) , true 10.5 tire, stock type suspension
https://www.youtube.com/watch?v=qDoJnIP3HgE
  #8  
Old 01-20-2020, 06:55 AM
Cliff R's Avatar
Cliff R Cliff R is offline
Ultimate Warrior
 
Join Date: Nov 2000
Location: Mount Vernon, Ohio 43050
Posts: 17,972
Default

Folks underestimate the potential of the small valve heads and still seek out big valve versions.

In many cases a small valve head will be a better bargain, and you can always put big valves in them anyhow.

Years ago we had a 455 short block ready to finish but the custom CNC ported KRE heads and roller cam coming with them were not going to make it in time to get the engine finished and in the car for the Norwalk race.

I reached under the work bench and grabbed up a set of 1969 #46 small valve heads. Did a quick seat and valve grind on them, better springs and screw in studs. Went to the parts room and grabbed up an older Crower flat hydraulic cam and finished the engine and got it installed in time to make the race.

The car was an 1981 Firebird, TH350, Continental converter and 4.10 gears with pretty tall DOT's. Right off the trailer it ran high 11's in the heat of August and it was pretty hot that year. I wasn't expecting much more than low to mid-12's out of it to be perfectly honest. You just never know with these things......FWIW......Cliff

__________________
If you can read this, thank a teacher. If you can read this in English, thank a Veteran!
https://cliffshighperformance.com/
73 Ventura, SOLD 455, 3740lbs, 11.30's at 120mph, 1977 Pontiac Q-jet, HO intake, HEI, 10" converter, 3.42 gears, DOT's, 7.20's at 96mph and still WAY under the roll bar rule. Best ET to date 7.18 at 97MPH (1/8th mile),
  #9  
Old 01-20-2020, 07:16 AM
steve25's Avatar
steve25 steve25 is online now
Ultimate Warrior
 
Join Date: May 2008
Location: Westchester NY
Posts: 14,632
Default

There's no carved in stone answer to that question as it by enlarge depends on how many cid the motor is and how it's Camed.

Some factors are right off the bat the small valve 1968 and up heads are down to 148.5 CCs of Intake port volume from the standard 154 to 156 CC size of the big valve heads, this kicks up the port velocity.

This fact right there brings down the torque and hp peak rpm of the small valve heads by 5% as compared to the big valve heads.
This makes them a great pick for the 326 motors and grocery getter 350 motors with 2.73 rear gears.

On bigger cid motors you can go 5% bigger in Cam duration if you want without having a low speed Torque drop off.

Any way you look at it though if your not with your back up against the wall when running these small valve heads of having too much compression then if your rebuilding them with new valve and need to do a valve job anyway then there's no doubt that installing the bigger valve sizes ( both Intake and Exh in most cases) is very worth more power.

Do a search in this section for what I posted about reworking 2 years ago, search under " The plus side of cheap small valve heads"

__________________
Wernher Von Braun warned before his retirement from NASA back in 1972, that the next world war would be against the ETs!
And he was not talking about 1/8 or 1/4 mile ETs!

1) 1940s 100% silver 4 cup tea server set.

Two dry rotted 14 x 10 Micky Thompson slicks.

1) un-mailed in gift coupon from a 1972 box of corn flakes.
Two pairs of brown leather flip flops, never seen more then 2 mph.

Education is what your left with once you forget things!
  #10  
Old 01-20-2020, 08:29 AM
Cliff R's Avatar
Cliff R Cliff R is offline
Ultimate Warrior
 
Join Date: Nov 2000
Location: Mount Vernon, Ohio 43050
Posts: 17,972
Default

Following that logic one could simply up the cam duration by 5 percent to pick up the lost airflow using smaller valve heads.

I know on the engine mentioned above we used a pretty "hefty" cam in it, 308/314, 248/256 @ .050" on a 108LSA. Idled like chit, stinky, but "BRUTAL" mid-range power. It was more or less just a parts engine filled with what we had readily available at the time to make time constraints.

It eventually did get it's custom CNC ported KRE heads and a custom ground solid roller cam which put it solidly into the high 10's. Also interesting is that the new combination doesn't "feel" as strong as the old one if you were evaluating the performance by "the seat of your pants". It's smooth/broad/flat power curve just pulls really hard like a big locomotive and lacks the explosive mid-range power it had with the iron heads and flat tappet cam combination even though it obviously puts considerably more power to the pavement at full throttle thru the 1/4 mile........Cliff

__________________
If you can read this, thank a teacher. If you can read this in English, thank a Veteran!
https://cliffshighperformance.com/
73 Ventura, SOLD 455, 3740lbs, 11.30's at 120mph, 1977 Pontiac Q-jet, HO intake, HEI, 10" converter, 3.42 gears, DOT's, 7.20's at 96mph and still WAY under the roll bar rule. Best ET to date 7.18 at 97MPH (1/8th mile),
  #11  
Old 01-20-2020, 10:38 AM
Skip Fix's Avatar
Skip Fix Skip Fix is offline
Ultimate Warrior
 
Join Date: Dec 1999
Location: Katy,TX USA
Posts: 20,541
Default

Correct numbers or not the 70 455 with small valve #15s was only 10 HP off the the 70 455 with #64 big valve heads, not sure if there was also a cam difference or not.

__________________
Skip Fix
1978 Trans Am original owner 10.99 @ 124 pump gas 455 E heads, NO Bird ever!
1981 Black SE Trans Am stockish 6X 400ci, turbo 301 on a stand
1965 GTO 4 barrel 3 speed project
2004 GTO Pulse Red stock motor computer tune 13.43@103.4
1964 Impala SS 409/470ci 600 HP stroker project
1979 Camaro IAII Edelbrock head 500" 695 HP 10.33@132 3595lbs
  #12  
Old 01-20-2020, 10:39 AM
steve25's Avatar
steve25 steve25 is online now
Ultimate Warrior
 
Join Date: May 2008
Location: Westchester NY
Posts: 14,632
Default

Totally true Cliff!

__________________
Wernher Von Braun warned before his retirement from NASA back in 1972, that the next world war would be against the ETs!
And he was not talking about 1/8 or 1/4 mile ETs!

1) 1940s 100% silver 4 cup tea server set.

Two dry rotted 14 x 10 Micky Thompson slicks.

1) un-mailed in gift coupon from a 1972 box of corn flakes.
Two pairs of brown leather flip flops, never seen more then 2 mph.

Education is what your left with once you forget things!
  #13  
Old 01-20-2020, 10:43 AM
steve25's Avatar
steve25 steve25 is online now
Ultimate Warrior
 
Join Date: May 2008
Location: Westchester NY
Posts: 14,632
Default

The 70 455 with 64 heads would have had the 068 Cam, the 1968 400 2bbl casting 15 head I can't say without looking it up, but for sure it would not have had the 068 Cam, maybe at best the 066 Cam if ordered in the GTO with that option, or if not that then the standard 2 bbl Cam of the day.

__________________
Wernher Von Braun warned before his retirement from NASA back in 1972, that the next world war would be against the ETs!
And he was not talking about 1/8 or 1/4 mile ETs!

1) 1940s 100% silver 4 cup tea server set.

Two dry rotted 14 x 10 Micky Thompson slicks.

1) un-mailed in gift coupon from a 1972 box of corn flakes.
Two pairs of brown leather flip flops, never seen more then 2 mph.

Education is what your left with once you forget things!
  #14  
Old 01-20-2020, 11:46 AM
Slick's Avatar
Slick Slick is offline
Senior Chief
 
Join Date: Sep 2008
Location: Pennsylvania
Posts: 323
Default

FWIW,

I had a totally stock, but well tuned 1970 Bonneville with the #15 head 455. 3.23 Safe-T-Track and turbo 400 (naturally), ~29" tall tires (P255/70R15 Radial T/As).

It was very fast for what it was. 13.90s at 97. My original 70 T/A RAIII, 3.31 Safe-T-Track, T400 ran 14.31 at 99.8. Runs at Capitol and Budds Creek.

Of course the T/A spun through all of first, the Bonneville was glued.

P cam in Bonneville (i.e. 067).

Bottom line: in mild form small valve heads can run!

Stuart

  #15  
Old 01-20-2020, 01:42 PM
SD455DJ SD455DJ is offline
Ultimate Warrior
 
Join Date: Aug 2009
Location: Grand Rapids, MI
Posts: 3,253
Default

Quote:
Originally Posted by Slick View Post
FWIW,

I had a totally stock, but well tuned 1970 Bonneville with the #15 head 455. 3.23 Safe-T-Track and turbo 400 (naturally), ~29" tall tires (P255/70R15 Radial T/As).

It was very fast for what it was. 13.90s at 97. My original 70 T/A RAIII, 3.31 Safe-T-Track, T400 ran 14.31 at 99.8. Runs at Capitol and Budds Creek.

Of course the T/A spun through all of first, the Bonneville was glued.

P cam in Bonneville (i.e. 067).

Bottom line: in mild form small valve heads can run!

Stuart
I totally agree with Stuart (Slick), Skip, and Cliff. These engines are sleepers and don't need large valves when the engine is fairly stock. Here is the dyno sheet of my '70 YH 455 360 hp stock rebuild motor with the original small valve #15 heads, a Summit 2802 cam and stock log manifolds. The compression was just a smidge under 10.0 to 1.

I believe it could have cracked 400 hp with more cam, but I was happy with the 390 hp/512 tq it made. I also believe it would have made 420 hp/525 tq with stock #64 large valve heads throughout the pull range.

Dennis
Attached Thumbnails
Click image for larger version

Name:	70 455 YH Dyno.PNG
Views:	133
Size:	104.9 KB
ID:	529281   Click image for larger version

Name:	IMG_20140811_092456_537_resized.jpg
Views:	120
Size:	84.0 KB
ID:	529282  

  #16  
Old 01-20-2020, 01:56 PM
Skip Fix's Avatar
Skip Fix Skip Fix is offline
Ultimate Warrior
 
Join Date: Dec 1999
Location: Katy,TX USA
Posts: 20,541
Default

Dennis I always wondered why the non AC/PS 70 motor had such a big WP pulley compared to others.

The 455 block and crank in my 78 TA started out as a '70 Bonneville 455 motor. First RAIV heads now Eddy heads. Kept the long tail shaft TH 400 as a back up core too!

__________________
Skip Fix
1978 Trans Am original owner 10.99 @ 124 pump gas 455 E heads, NO Bird ever!
1981 Black SE Trans Am stockish 6X 400ci, turbo 301 on a stand
1965 GTO 4 barrel 3 speed project
2004 GTO Pulse Red stock motor computer tune 13.43@103.4
1964 Impala SS 409/470ci 600 HP stroker project
1979 Camaro IAII Edelbrock head 500" 695 HP 10.33@132 3595lbs
  #17  
Old 01-20-2020, 02:06 PM
SD455DJ SD455DJ is offline
Ultimate Warrior
 
Join Date: Aug 2009
Location: Grand Rapids, MI
Posts: 3,253
Default

Quote:
Originally Posted by Skip Fix View Post
Dennis I always wondered why the non AC/PS 70 motor had such a big WP pulley compared to others.

The 455 block and crank in my 78 TA started out as a '70 Bonneville 455 motor. First RAIV heads now Eddy heads. Kept the long tail shaft TH 400 as a back up core too!
Skip,

This YH 455 was the replacement motor for the original 350 2-bbl engine that we removed in the LeMans 4-speed that has manual steering, so the WP pulley in the picture is from the LeMans' 350 motor. Yeah, they are huge and maybe too big to work properly with PS? I know AC cars had smaller pulleys to spin the WP faster to circulate the coolant quicker.

I'm sure you told us before, but how did your TA run with the RAIV heads on it?

Dennis

  #18  
Old 01-20-2020, 02:18 PM
Skip Fix's Avatar
Skip Fix Skip Fix is offline
Ultimate Warrior
 
Join Date: Dec 1999
Location: Katy,TX USA
Posts: 20,541
Default

Very conservative dyno through a full exhaust(real mufflers not dyno big mufflers) made 420 HP with an UD 288/296 HFT cam HO intake and 73 SD SR Q jet. In the car with stiff autocross suspension and sticky DOTs and 3.42s ran 12 teens @ 117 through a 3" H pipe and 2.5" tailpipe exhaust system Weight was about 3950. Was a blast with road race slicks autocrossing also.

I did have to run race gas mixed in it even dropping the CR my shaving the pistons and a 0.080 down the hole deck.

__________________
Skip Fix
1978 Trans Am original owner 10.99 @ 124 pump gas 455 E heads, NO Bird ever!
1981 Black SE Trans Am stockish 6X 400ci, turbo 301 on a stand
1965 GTO 4 barrel 3 speed project
2004 GTO Pulse Red stock motor computer tune 13.43@103.4
1964 Impala SS 409/470ci 600 HP stroker project
1979 Camaro IAII Edelbrock head 500" 695 HP 10.33@132 3595lbs

Last edited by Skip Fix; 01-20-2020 at 02:29 PM.
  #19  
Old 01-20-2020, 02:38 PM
geeteeohguy's Avatar
geeteeohguy geeteeohguy is offline
Ultimate Warrior
 
Join Date: Dec 2009
Location: Fresno, California
Posts: 5,313
Default

Quote:
Originally Posted by Skip Fix View Post
Correct numbers or not the 70 455 with small valve #15s was only 10 HP off the the 70 455 with #64 big valve heads, not sure if there was also a cam difference or not.
I have been running these exact heads on my '67 400 in my GTO ragtop for the past 10-12 years. With an 068 cam, stock q-jet, TH400 and 2.56 gears, it's a great economical high speed low rpm road car. The only thing I did was add screw in studs. Not as strong as it used to be with the 3.36 gear and 670 heads, but it runs on pump gas, which the stock combo wouldn't.

__________________
Jeff
  #20  
Old 01-20-2020, 03:51 PM
Skip Fix's Avatar
Skip Fix Skip Fix is offline
Ultimate Warrior
 
Join Date: Dec 1999
Location: Katy,TX USA
Posts: 20,541
Default

I always thought #15s would make a good pump gas 400. Why I kept those off my 455, but probably will never use them.

__________________
Skip Fix
1978 Trans Am original owner 10.99 @ 124 pump gas 455 E heads, NO Bird ever!
1981 Black SE Trans Am stockish 6X 400ci, turbo 301 on a stand
1965 GTO 4 barrel 3 speed project
2004 GTO Pulse Red stock motor computer tune 13.43@103.4
1964 Impala SS 409/470ci 600 HP stroker project
1979 Camaro IAII Edelbrock head 500" 695 HP 10.33@132 3595lbs
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:51 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017