FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
|
SOLD Parts The parts in here have already been sold. The topics will be kept for a few months for reference. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
31 spline Moser axles for sale...
I have a set of Moser axles for a 9" rear for sale . They are 31 spline with bearings ready to bolt one. Very good condition. I up graded to 35 spline .They are 27 1/8 and 31 1/8 5x4 3/4 2.430. these are small ford bearings with built in seals/ o-ring.. 1/2 X 3" long studs.
$250.00 + shipping. Thank You....
__________________
My Half AN Injun..... |
#2
|
||||
|
||||
The axles do have a GM lug bolt pattern....
__________________
My Half AN Injun..... |
#3
|
||||
|
||||
bump
__________________
My Half AN Injun..... |
#4
|
||||
|
||||
bump
__________________
My Half AN Injun..... |
#5
|
||||
|
||||
bump
__________________
My Half AN Injun..... |
#6
|
||||
|
||||
bump...
__________________
My Half AN Injun..... |
#7
|
||||
|
||||
bump
__________________
My Half AN Injun..... |
#8
|
||||
|
||||
bump
__________________
My Half AN Injun..... |
#9
|
||||
|
||||
Still for sale
__________________
My Half AN Injun..... |
#10
|
||||
|
||||
bump
__________________
My Half AN Injun..... |
#11
|
||||
|
||||
Im surprised know one is interested in these.. They were bought new from Moser by me and used for just a season and taken off because I up graded to 35spline . I paid 500.00 for them . There good for 800 hp !
__________________
My Half AN Injun..... |
#12
|
||||
|
||||
What is the width of the housing?
|
#13
|
||||
|
||||
That's a good question , I don't know.
I do know the rear came out of a stock 1969 mustang . So what ever the rear would of measured in one of those. Ill measure it tomorrow though...
__________________
My Half AN Injun..... |
#14
|
||||
|
||||
Looks like its 54.1/4 from the back of each backing plate to backing plate. I measured it under the car so it could possibly be a little different then that number. I did post the axles sizes in my first post though. Those numbers should be all you need as long as you know your current axles size.
__________________
My Half AN Injun..... |
#15
|
||||
|
||||
here are some pictures
__________________
My Half AN Injun..... |
#16
|
||||
|
||||
Can different bearings be pressed on for Torino ends?
|
#17
|
||||
|
||||
Why are they different? What size are they 3 1/2 ? Ill measure the axle so you can compare your bearing ID size to the number I get..
__________________
My Half AN Injun..... |
#18
|
||||
|
||||
The axle measures 1.378 where the bearing gets pressed on.. So what ever bearing you have has to be a few thousandths smaller then that. I don't know off hand what the interference size is. If you call Moser or strange they will know...
__________________
My Half AN Injun..... |
#19
|
||||
|
||||
What size are your bearings?
__________________
My Half AN Injun..... |
#20
|
||||
|
||||
Torino might be the same as mustang no?
__________________
My Half AN Injun..... |
|
|