 |
|
| SOLD Parts The parts in here have already been sold. The topics will be kept for a few months for reference. |
|
|
Thread Tools | Display Modes |
|
#1
01-10-2020, 08:04 PM
|
||||
|
||||
Thinking about selling my like new
Mickey Thompson Cross-Ram (I have two - one with mods that I made for 65 heads that is not for sale and:
A second Mickey Thompson Crossram that is like new (just been sitting on the shelf for many years). This cross-ram fits the earlier 64 and older heads unless it is modded (like the one I did for my 65+ heads). I met a guy at Norwalk who machined off the water cross-over of his intake, trimmed the rear "ears" of the intake, and added some weld to the bottom of the intake runners and cleaned up the gasket surfaces. (1964 and earlier intake ports are actually HIGHER vs the 65 and later stuff.) He modded it to fit on his 65+ engine. Again, MY intake for sale is a 64 and earlier intake with no mods. Intake goes for $600 plus shipping in the USA. Very large intake as far as fitting into a shipping box so shipping will be more expensive vs a basic aluminum 4 BBL intake. Tom V.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
|
#3
01-10-2020, 10:37 PM
|
||||
|
||||
|
This guy wants $5,000 for a NOS M/T Pontiac Cross-Ram
Picture Attached You can see that the shipping box would be pretty large. Mine is $600 plus shipping Tom V.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
|
#4
01-10-2020, 11:58 PM
|
||||
|
||||
|
Wait a minute, is this to good to be true?
__________________
" Is wearing a helmet illegal" Mike Kerr 1-29-09 |
|
#5
01-11-2020, 01:02 PM
|
||||
|
||||
|
I personally have had the intake for many years.
Many years ago, I had 3 of the intakes I owned, modded for a Plenum Cross-over Balance Tube and to allow the intake to fit on a 65+ Pontiac Engine cylinder head. Richard Cole has one, Skip Fix has one, and I have one (modded Intakes for 65+ heads). The 64 original M/T Cross-Ram means little to me except I own one. The guy selling the $5,000 one is on drugs. The intake might be worth $750 NOS tops. I am selling for $600 plus shipping. A proper fair price. What part do you not understand? Tom V.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
|
#7
01-11-2020, 02:53 PM
|
||||
|
||||
|
I've also got one Tom, And mine has been modded too.
They are a neat looking piece and I plan on using mine on my 57 Pontiac some day. GT. |
|
#8
01-11-2020, 05:02 PM
|
||||
|
||||
|
Intake is sold to HotRodDan
Tom Vaught
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
|
|
The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.
Linear Mode
