[Uncle Phil]

I'm needing a working blower switch (that fits on top of the controller) and also a control cable that connects the controller to the defrost duct on the heater box. (I have the other 2 cables). All of these for a 68 FB.

I will offer up a set of drum brake spindles for a 68 FB.

Thanks!!

Phil

[Tone]

I could trade the windshield trim and bench seat from a 73 Lemans if anyone needs it....


I'd be interested in an intake or carb possibly. I'm still working on getting dual exhaust...so if you have pipe laying around....lemme know.

[cruze69gto]

I have a YB code 350 bare block, standard bore. If anyone is interasted. I will be going to Norwalk can bring if someone needs it.

Mike

[fasteddy]

I need 2ea 63 Tempest hood bolts with retainer springs-any help would be greatly appreciated. I had all 4 but a buddy tossed the 2 that fell out in the steel scrap bin.

[64-389]

GOBRDGO, PM sent for 350 tranny....

I have a '64 Star cheif hood and trunk lid. A little rust on both, definitely restorable. Should fit Bonne or Cat..

Also have '64 big car hydromatic transmission (R on bottom)...works good.

[winbub]

AVAILABLE (but ya gotta come git it)

'66 Tempest Custom Front Bench Seat
'66 tempest Custom Doors (2)
'66/67 GTO inner fender wells (2) - need work

[limejudge69]

I have the vinyl top chrome side/corner trim and clips for 69 Grand Prix. All will need polishing, but no pits. One piece was bent slightly during removal, but should be fixable. PM if interested and I'll send it to ya!

[FirebirdTA]

I have a 79 T/A shell that someone can have. Body is mostly rust free. Only the floor has some surface rust and the trunk is rusted out. Tail panel, quarter panels (passenger quarter panel has a dent above the wheel well),T-top roof, cowl/firewall (does have about a 12" crack) and frame are completely rust free. Windshield is good but has a few chips and the back window is good. I do not want to take it to be scraped with good body panels. It is in Tulsa OK.

Eric

[bristew8]

I have 74 400 block set up for 4- bolt main pontiac 350 block various pullies, 77 400 intake couple of HEI dist. firebird hood ( base) Looking for heat and a/c boxes inside and out 77-79 bird and trans crossmember th350 for 77-79 bird

[fried boloney]

needs rebuilt,probably under 50,000 miles,was replaced under warranty because it got some antifreeze in one cyl and FUBARRED the piston. Pieces of piston scored the cyl wall.I have the complete engine minus the supercharger and exh. manifolds. Free,pickup in SC

[Blowd]

These look like they were left in a hail storm and repaired with a ball-peen hammer. OK seriously, exterior patches on both lower, old damage to leading edge and behind/on wheel well.
Got these as part of my most recent backyard find. They are beyond my skills/patience, but I know repros aren't that great and maybe someone thinks these aren't that bad.
Free to good home but will not ship. I just don't have time to mess with at this price. Might meet or deliver for consideration. I'm NW of Houston (Cypress) TX. Post here for first dibs, PM, or email gr8dealz@aol.com for info/details.

[lazlo]

For my project 71 GTO Vert... looking for a set of stock exhaust manifolds for my 72 455 motor with 1967 061 heads. It's got new headers on it now & I would rather have stock.. Got my 71 in a million pieces & I'm sure I'll have a ton of extras when I get it back together

[Schoust]

Guy's I am also looking for the same set of logs for a 72 455 if anyone has anything let me know after Lazlo that is.......

[techteacher5561]

BB1968,
sent you a email on the hood and bumper,

I'd have to offer a 68 350 block w 17 heads in the very near future due to my new motor being built.

possibly a Torquer intake (not a T2) trying to think or what I've accumulated.
an HEI working now not sure how good , bought a new/used one.

Howard

[1967firebirdsg]

Hello,i need a set of frame mounts for a 67-69 firebird.Also a Dominator...

[sharkbite]

Looking for drip rail molding and vinyl top trim for 72 GTO. I have a few pieces of each but need to complete the sets. Thanks

[elcaminobill]

Originally Posted by fried boloney

Anybody near the upastate SC area have a good clean Rally II wheel? Doesnt matter what size or bolt pattern ,I just want one I can paint up for a display piece.Could also use a trim ring if you have it,not looking for show quality just a clean presentable piece

I'm in the Greenville area and probably help you. If I don't have one, I know a guy selling a set of 5. PM me.

Thanks,
Bill

[elcaminobill]

Originally Posted by fried boloney

needs rebuilt,probably under 50,000 miles,was replaced under warranty because it got some antifreeze in one cyl and FUBARRED the piston. Pieces of piston scored the cyl wall.I have the complete engine minus the supercharger and exh. manifolds. Free,pickup in SC

I'd be interested in this if you still have it.

[hpp]

Have a Holley Streer Avenger 670CFM carb bought it 7/29/06
looking for a good rebuilt Quadrajet.

[Rack776]

*Fiero 2 Cam Quad 4 Swap *Drag Car Body
I'm not looking to make money I just dont want to waste a good engine!

I'm looking into purchaseing a new car soon and I would hate to see the one I have now go to the scrap yard.
If anyone wants to use it for a project let me know, the insurance runs out in May after that it goes to the yard.

Its a 1991 Grand Am SE with a super strong Quad 4 & Automatic Trans
Great Air Conditioning & Factory Finned 5 Spoke Aluminum Wheels. New Exhaust
and Power Steering Pump.
Oil was changed regularly It has 103,000 miles mostly highway & had new head gasket at 50,000.

I figure someone could use the twin cam engine in a fiero or build a tube chassis drag car out of the body.
If it did not run so strong I would just junk it with out a second thought.

It has a clear title but The Body is starting to rust out under the rear coil spring mounts and I dont think its safe enugh to be a passenger car anymore. the outside is ok, the interior is shot. Lights, Lenses & Bumpers are ok, driver door has a small dent at the top.

It can't sit around long to part it out so it gota go as a whole car if possible.
If you need something off it bad enugh and I'll consider taking it off for you.

I just want scrap value & title transfer money for it. (Or I can trade for 70-81 T/A parts
or Pontiac V8 engine parts I'll take any available)

It needs to be picked up around Allentown PA area.

Jason Rackawack
rack776@yahoo.com
I can respond to emails Monday - Friday