#21  
Old 01-13-2021, 12:23 PM
Chief of the 60's Chief of the 60's is offline
Suspended
 
Join Date: Nov 2017
Location: On the Rez
Posts: 3,233
Default

Its not a question about whether or not an aluminum driveshaft can work, they obviously do.

The question is whether its worth saving a few bucks by using a "used" factory aluminum driveshaft out of a junkyard.

I say, based on what I know and have seen, hell NO

  #22  
Old 01-13-2021, 01:17 PM
RocktimusPryme's Avatar
RocktimusPryme RocktimusPryme is offline
Ultimate Warrior
 
Join Date: Jul 2014
Location: Bedford, IN
Posts: 2,165
Default

As far as the basic theory here I had in mind when I began the conversation, we are getting a bit hung up on the aluminum part of it. Are basically all OEM shafts aluminum now? Would it be difficult to find a big factory steel DS?

__________________
1967 Firebird 462 580hp/590ftlbs
1962 Pontiac Catalina Safari Swapped in Turd of an Olds 455
Owner/Creator Catfish Motorsports
https://www.youtube.com/@CatfishMotorsports
  #23  
Old 01-13-2021, 01:21 PM
JLMounce JLMounce is offline
Ultimate Warrior
 
Join Date: Sep 2005
Location: Greeley, Colorado
Posts: 3,679
Send a message via AIM to JLMounce
Default

Quote:
Originally Posted by RocktimusPryme View Post
As far as the basic theory here I had in mind when I began the conversation, we are getting a bit hung up on the aluminum part of it. Are basically all OEM shafts aluminum now? Would it be difficult to find a big factory steel DS?
My understanding with the modern stuff is yes. There's going to be basically two types of construction you see. Either a 1 piece aluminum shaft or a 2 piece steel shaft with a center carrier bearing.

__________________
-Jason
1969 Pontiac Firebird
  #24  
Old 01-13-2021, 01:25 PM
Chief of the 60's Chief of the 60's is offline
Suspended
 
Join Date: Nov 2017
Location: On the Rez
Posts: 3,233
Default

Funny thing is, my Dodge Magnum Wagon has a 2 piece with carrier bearing driveshaft. Now, I don't know if all LX (300, Challenger, Charger, Magnum) cars do but mine does.

  #25  
Old 01-13-2021, 01:33 PM
JLMounce JLMounce is offline
Ultimate Warrior
 
Join Date: Sep 2005
Location: Greeley, Colorado
Posts: 3,679
Send a message via AIM to JLMounce
Default

Quote:
Originally Posted by Chief of the 60's View Post
Funny thing is, my Dodge Magnum Wagon has a 2 piece with carrier bearing driveshaft. Now, I don't know if all LX (300, Challenger, Charger, Magnum) cars do but mine does.
The modern mustangs I've had S197 chassis and beyond, all had two piece shafts with carrier bearings. I know the Challenger's use two piece shafts as well.

My 2006 Tundra as equipped like that as well.

I think it's become fairly common to see that.

__________________
-Jason
1969 Pontiac Firebird
  #26  
Old 01-13-2021, 01:59 PM
Bill Eveland's Avatar
Bill Eveland Bill Eveland is offline
Ultimate Warrior
 
Join Date: Apr 2004
Location: Glasford Il
Posts: 3,650
Default

I paid around 300 for my 3" CM Strange shaft that came with 1350 u joints plus their yoke on trans and rear end . I don't see worth saving much with trying to make something else used work. Hardly any factory shaft is going to come with 1350 u joints. I know this is the street section, put pay for something good once and be done.

__________________
Illinois Outlaw Gassers

6.27@107
9.97@131
  #27  
Old 01-13-2021, 03:13 PM
RocktimusPryme's Avatar
RocktimusPryme RocktimusPryme is offline
Ultimate Warrior
 
Join Date: Jul 2014
Location: Bedford, IN
Posts: 2,165
Default

Those strange shafts are a pretty good deal.

__________________
1967 Firebird 462 580hp/590ftlbs
1962 Pontiac Catalina Safari Swapped in Turd of an Olds 455
Owner/Creator Catfish Motorsports
https://www.youtube.com/@CatfishMotorsports
  #28  
Old 01-13-2021, 03:16 PM
ta man ta man is offline
Ultimate Warrior
 
Join Date: Apr 2006
Location: Clinton,Ontario,Canada
Posts: 5,346
Default

Quote:
Originally Posted by AG View Post
This. I also got the same driveshaft from Strange and I'll never have to be concerned about failure. You can look up a chart that shows the critical RPM for a given material, diameter and length to decide what you need.
I know the diameter and the length dropped the 80 percent critical rpm to just under 6800 rpm..but it can handle 1500hp if I remember.

__________________

466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2
373 gears 3200 Continental Convertor
best et 10.679/127.5/1.533 60ft
308 gears best et 10.76/125.64/1.5471

Last edited by ta man; 01-13-2021 at 03:22 PM.
  #29  
Old 01-13-2021, 03:22 PM
dataway's Avatar
dataway dataway is offline
Ultimate Warrior
 
Join Date: Jan 2012
Location: Saratoga NY
Posts: 8,921
Default

The driveshaft on my 2011 GMC truck is steel, at least that's what the rust tells me.

Probably long enough to modify for any car out there.

  #30  
Old 01-13-2021, 03:52 PM
Formulajones's Avatar
Formulajones Formulajones is offline
Ultimate Warrior
 
Join Date: Jan 2012
Posts: 10,788
Default

Is it a short bed or single cab?

My understanding from our local driveline shop is it's the length of the driveshaft needed that determines the material, and if it's a long shaft and made of steel, there is a certain point where a carrier bearing is needed so the shaft can be made in 2 shorter pieces. Really long steel shafts aren't a good idea, They get too heavy and as mentioned critical speed becomes an issue, earlier I mentioned they start whipping if too long and heavy.

Think "jump rope"

Aluminum is lighter and will have a much higher critical speed before that occurs. So in some cases when the factory didn't want to use a carrier bearing to make a 2 piece steel shaft for what ever reason, they would use aluminum, make it one long shaft and done.

__________________
2019 Pontiac Heaven class winner

https://youtu.be/XqEydRRRwqE
  #31  
Old 01-13-2021, 03:59 PM
RocktimusPryme's Avatar
RocktimusPryme RocktimusPryme is offline
Ultimate Warrior
 
Join Date: Jul 2014
Location: Bedford, IN
Posts: 2,165
Default

Im in the same boat with my Ram. I feel like Ive seen some small surface rust which would make me think its steel. Its a short bed. So maybe the short box vehicles get a steel shaft.

__________________
1967 Firebird 462 580hp/590ftlbs
1962 Pontiac Catalina Safari Swapped in Turd of an Olds 455
Owner/Creator Catfish Motorsports
https://www.youtube.com/@CatfishMotorsports
  #32  
Old 01-13-2021, 06:19 PM
dataway's Avatar
dataway dataway is offline
Ultimate Warrior
 
Join Date: Jan 2012
Location: Saratoga NY
Posts: 8,921
Default

My truck is a single cab, with the medium length bed ... 7'6" about. So probably shorter than some trucks.

  #33  
Old 01-13-2021, 10:22 PM
Tom Vaught's Avatar
Tom Vaught Tom Vaught is offline
Boost Engineer
 
Join Date: Dec 2001
Location: The United States of America
Posts: 31,294
Default

Quote:
Originally Posted by Formulajones View Post
Is it a short bed or single cab?

My understanding from our local driveline shop is it's the length of the driveshaft needed that determines the material, and if it's a long shaft and made of steel, there is a certain point where a carrier bearing is needed so the shaft can be made in 2 shorter pieces. Really long steel shafts aren't a good idea, They get too heavy and as mentioned critical speed becomes an issue, earlier I mentioned they start whipping if too long and heavy.

Think "jump rope"

Aluminum is lighter and will have a much higher critical speed before that occurs. So in some cases when the factory didn't want to use a carrier bearing to make a 2 piece steel shaft for what ever reason, they would use aluminum, make it one long shaft and done.
Critical Speed, as mentioned with an example in my previous posts can not be ignored. A properly designed and fabricated aluminum driveshaft from a quality supplier or a new driveshaft modified for the proper length for the application is the way to go.

There is a point with "AGE" and "Duty Cycle" (where even the best parts fail eventually). Put a driveshaft loop on the vehicle and save your vehicle from
potential sheet metal replacement down the road.

__________________
"Engineers do stuff for reasons" Tom Vaught

Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward.
  #34  
Old 01-14-2021, 10:52 AM
Formulajones's Avatar
Formulajones Formulajones is offline
Ultimate Warrior
 
Join Date: Jan 2012
Posts: 10,788
Default

Quote:
Originally Posted by Tom Vaught View Post
Critical Speed, as mentioned with an example in my previous posts can not be ignored. A properly designed and fabricated aluminum driveshaft from a quality supplier or a new driveshaft modified for the proper length for the application is the way to go.

There is a point with "AGE" and "Duty Cycle" (where even the best parts fail eventually). Put a driveshaft loop on the vehicle and save your vehicle from
potential sheet metal replacement down the road.
It's probably one of the reasons why, as I mentioned earlier, our driveline shop does not work on used aluminum driveshafts. He'll build you a nice shiny brand new one though

However, he'll work on and modify used steel driveshafts all day long

__________________
2019 Pontiac Heaven class winner

https://youtu.be/XqEydRRRwqE
  #35  
Old 01-14-2021, 01:56 PM
AG's Avatar
AG AG is offline
Ultimate Warrior
 
Join Date: Feb 2000
Location: NH
Posts: 3,240
Default

The critical RPM for my Strange DS is 7800 rpm if I remember correctly and I go across the line at 6700 rpm. It is 3" CM, if I was going to a higher rpm I would have gone with a 3.5" CM shaft.

__________________
1967 Firechicken, 499", Edl heads, 262/266@0.050" duration and 0.627"/0.643 lift SR cam, 3.90 gear, 28" tire, 3550#. 10.01@134.3 mph with a 1.45 60'. Still WAY under the rollbar rule.
  #36  
Old 01-14-2021, 02:03 PM
Chief of the 60's Chief of the 60's is offline
Suspended
 
Join Date: Nov 2017
Location: On the Rez
Posts: 3,233
Default

Quote:
Originally Posted by AG View Post
The critical RPM for my Strange DS is 7800 rpm if I remember correctly and I go across the line at 6700 rpm. It is 3" CM, if I was going to a higher rpm I would have gone with a 3.5" CM shaft.
So your tranny is 1:1 in final gear?

  #37  
Old 01-14-2021, 06:25 PM
ta man ta man is offline
Ultimate Warrior
 
Join Date: Apr 2006
Location: Clinton,Ontario,Canada
Posts: 5,346
Default

Quote:
Originally Posted by AG View Post
The critical RPM for my Strange DS is 7800 rpm if I remember correctly and I go across the line at 6700 rpm. It is 3" CM, if I was going to a higher rpm I would have gone with a 3.5" CM shaft.
That was my way of thinking as well to stay with a 3 inch..time may tell if the rpms creep up over time with any new engine changes.

__________________

466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2
373 gears 3200 Continental Convertor
best et 10.679/127.5/1.533 60ft
308 gears best et 10.76/125.64/1.5471
  #38  
Old 01-14-2021, 09:01 PM
AG's Avatar
AG AG is offline
Ultimate Warrior
 
Join Date: Feb 2000
Location: NH
Posts: 3,240
Default

Quote:
Originally Posted by Chief of the 60's View Post
So your tranny is 1:1 in final gear?
Yes, TH400.

__________________
1967 Firechicken, 499", Edl heads, 262/266@0.050" duration and 0.627"/0.643 lift SR cam, 3.90 gear, 28" tire, 3550#. 10.01@134.3 mph with a 1.45 60'. Still WAY under the rollbar rule.
  #39  
Old 01-14-2021, 09:50 PM
Chief of the 60's Chief of the 60's is offline
Suspended
 
Join Date: Nov 2017
Location: On the Rez
Posts: 3,233
Default

Quote:
Originally Posted by AG View Post
Yes, TH400.
Just curious. Some do not. That, obviously effects flywheel RPM vs. tail shaft RPM. That effects driveshaft RPM

  #40  
Old 01-14-2021, 09:55 PM
JLMounce JLMounce is offline
Ultimate Warrior
 
Join Date: Sep 2005
Location: Greeley, Colorado
Posts: 3,679
Send a message via AIM to JLMounce
Default

Technically speaking, unless you’re running a lockup converter, your DS rpm will still be less than engine RPM due to torque converter slippage, even if your final is 1:1

But that’s splitting hairs of course.

__________________
-Jason
1969 Pontiac Firebird
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:03 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017