#1  
Old 01-24-2023, 03:50 PM
grivera's Avatar
grivera grivera is offline
Ultimate Warrior
 
Join Date: Feb 2005
Location: Just south of Baltimore
Posts: 4,891
Default Fixed Orifice PCV

In the Facebook Sniper EFI forum I read that a fixed orifice style PCV is preferred when using EFI - apparently it helps with idle. Has anyone experimented with this and also is anyone aware of a fixed orifice style PCV that looks and fits in old Pontiacs like ours.

__________________
Will Rivera

'69 Firebird 400/461, 290+ E D-Ports, HR 230/236, 4l80E, 8.5 Rear, 3.55 gears
'64 LeMans 400/461, #16 Heads, HR 230/236, TKO600, 9inch Rear, 3.89 gears
'69 LeMans Vert, 350, #47 heads: Non-running project
  #2  
Old 01-24-2023, 04:09 PM
JLMounce JLMounce is online now
Ultimate Warrior
 
Join Date: Sep 2005
Location: Greeley, Colorado
Posts: 3,679
Send a message via AIM to JLMounce
Default

I went from a standard PCV system to a draft style system that is close to a fixed oriface PCV on my FiTech. I didn't notice any change in idle characteristics, nor did I have to make any tuning changes.

The item that made the biggest difference in idle quality was moving to timing control. Being able to dump in idle timing and letting the system idle stabilize by adjusting advance relative to fuel made a fairly dramatic difference in both idle quality, temperature control and idle vacuum. I gained over 2" Hg at idle by going to timing control and commanding about 24 degrees of initial advance.

This worked so well, that my once "somewhat rowdy" 455 with a 232/238 112 cam behaves and sounds as if it has more of a factory type cam in it.

__________________
-Jason
1969 Pontiac Firebird
  #3  
Old 01-24-2023, 04:25 PM
Scott65's Avatar
Scott65 Scott65 is offline
Ultimate Warrior
 
Join Date: Jan 2002
Location: Houston, Texas
Posts: 1,991
Default

I've tuned mine with a pcv system and with a draft style open breather set up. They each react differently because of the vacuum differences, but I can attain a great idle with either.

__________________
'65 Tempest 467 3650# 11.30@120.31
The Following User Says Thank You to Scott65 For This Useful Post:
  #4  
Old 01-24-2023, 04:36 PM
Formulajones's Avatar
Formulajones Formulajones is offline
Ultimate Warrior
 
Join Date: Jan 2012
Posts: 10,794
Default

I switched the Chevelle over to fixed orifice PCV, after I had run the Sniper setup for more than a year with a regular PCV.

On mine, going to a fixed orifice, basically made the vacuum leak much smaller and caused the IAC counts to rise a bit to bring the idle back up where it was commanding. Once warmed up it's not a big deal but when it's cold it really tightened up the window I had for a high speed cold idle, basically pegging the IAC at 100 when cold to barely maintain an idle.

What it boils down to for me, and something I complained about very early on when we bought these Snipers, is that the IAC could stand to be a bit bigger for these larger engines with big camshafts that have a bunch of overlap.

I've played around with drilling the fixed orifice, I think I'm up to 3/32" or so and it hasn't really made a bunch of difference. Of course that's not even close to the near 1/4" or 5/16 hole the regular PCV had, LOL

Funny this all came up because I was going to switch it back over to the regular PCV today. I never had any drivability or running issues with it so not sure why they preach that so much over on the Holley forum.

The GTO got switched over to a vacuum pump so the engine is totally sealed, eliminating the PCV. But that was done for other reasons.

__________________
2019 Pontiac Heaven class winner

https://youtu.be/XqEydRRRwqE
  #5  
Old 01-26-2023, 08:41 PM
grivera's Avatar
grivera grivera is offline
Ultimate Warrior
 
Join Date: Feb 2005
Location: Just south of Baltimore
Posts: 4,891
Default

Which fixed orifice PVC did you use?

__________________
Will Rivera

'69 Firebird 400/461, 290+ E D-Ports, HR 230/236, 4l80E, 8.5 Rear, 3.55 gears
'64 LeMans 400/461, #16 Heads, HR 230/236, TKO600, 9inch Rear, 3.89 gears
'69 LeMans Vert, 350, #47 heads: Non-running project
  #6  
Old 01-26-2023, 08:55 PM
Formulajones's Avatar
Formulajones Formulajones is offline
Ultimate Warrior
 
Join Date: Jan 2012
Posts: 10,794
Default

Quote:
Originally Posted by grivera View Post
Which fixed orifice PVC did you use?
Oooof, honestly I'm not sure if there are a bunch of choices or not. I grabbed one off the shelf at the local store with a straight up 3/8 hose nipple that would work on my Chevelle. Same thing you would see in a Pontiac valley pan.

From what I understand though, they all pretty much have just a 2mm or a 3mm hole size in them. Not very big at all. Basically they are just a gutted PCV with a tiny hole in the bottom. A controlled vacuum leak....

I removed mine yesterday and reinstalled the standard PCV. But I'm just sort of playing around with the differences to understand more how it affects the fuel table.

__________________
2019 Pontiac Heaven class winner

https://youtu.be/XqEydRRRwqE
  #7  
Old 01-27-2023, 12:22 PM
grivera's Avatar
grivera grivera is offline
Ultimate Warrior
 
Join Date: Feb 2005
Location: Just south of Baltimore
Posts: 4,891
Default

Thanks- I’ve been searching on line but will take a look at AA and AZ…

__________________
Will Rivera

'69 Firebird 400/461, 290+ E D-Ports, HR 230/236, 4l80E, 8.5 Rear, 3.55 gears
'64 LeMans 400/461, #16 Heads, HR 230/236, TKO600, 9inch Rear, 3.89 gears
'69 LeMans Vert, 350, #47 heads: Non-running project
  #8  
Old 01-30-2023, 01:05 PM
Formula8's Avatar
Formula8 Formula8 is offline
Ultimate Warrior
 
Join Date: Feb 2004
Location: Chicago
Posts: 2,308
Default

Here is the link to the one I used: https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

I used it form the get go so I don't have anything to compare it against. I just had to put a piece of electrical shrink wrap around the bottom to fit a bit snugger in my stock PCV gasket.

__________________
71 Formula 433, Splayed cap 400 block, 4" stroke Scat forged crank, 6.8 Eagle rods, custom Autotec pistons. SD 295 KRE D ports, Old faithful hybrid roller, Torker II, Holley Sniper Stealth, Tribal Tubes, TKO 600, 3.73 Eaton posi.
The Following User Says Thank You to Formula8 For This Useful Post:
  #9  
Old 02-01-2023, 01:17 AM
Geoff Geoff is offline
Ultimate Warrior
 
Join Date: Jul 2005
Location: Australia
Posts: 2,470
Default

I have on many big cammed engines used a fixed orifice PCV. On street cars here, a working PCV is reqd for registration. I calculated the orifice area of a stock PCV at idle & came up with a round hole of 7/64" diam.
I cut open the PCV, discard the innards & braze in a disc, in which I drill a 7/64" hole. Then braze the PCV back together.

Have done many over the years & work well.

  #10  
Old 02-03-2023, 09:13 PM
jrh3405 jrh3405 is offline
Junior Member
 
Join Date: May 2008
Posts: 7
Default

I've had good luck with the ME Wagner dual flow pcv valve for my Pontiac, it's adjustable and or fixed orfice for efi.

  #11  
Old 02-04-2023, 10:53 PM
grivera's Avatar
grivera grivera is offline
Ultimate Warrior
 
Join Date: Feb 2005
Location: Just south of Baltimore
Posts: 4,891
Default

Thanks all

__________________
Will Rivera

'69 Firebird 400/461, 290+ E D-Ports, HR 230/236, 4l80E, 8.5 Rear, 3.55 gears
'64 LeMans 400/461, #16 Heads, HR 230/236, TKO600, 9inch Rear, 3.89 gears
'69 LeMans Vert, 350, #47 heads: Non-running project
  #12  
Old 02-05-2023, 08:46 PM
Formulajones's Avatar
Formulajones Formulajones is offline
Ultimate Warrior
 
Join Date: Jan 2012
Posts: 10,794
Default

Now that I've had a few days to drive the car and actually work on the tune today, for sure a regular pcv has changed things over the fixed orifice.
I had that fixed orifice drilled to 3/32 and it apparently still wasn't enough.

The new pcv specified for the engine has the closed loop now adding 3-4 percent more fuel thanks to the larger "vacuum leak", the iac counts are lower to compensate thanks to the slightly higher idle. This has my cold start rpm back to a more reasonable area (IAC isn't really big enough for a big engine with a rowdy cam)
Overall after mild tweaks in the tune a regular pcv seems to help this particular engine deal with an inadequate IAC. It's actually now idling with a pinch more vacuum
(Lower map)

Similar IAC issues I've dealt with on dad's engine since his engine is completely sealed and using a vacuum pump, so no pcv with a controlled vacuum leak.

Just thought I'd share

__________________
2019 Pontiac Heaven class winner

https://youtu.be/XqEydRRRwqE
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:01 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017