#1  
Old 09-28-2024, 12:36 PM
kingbuzzo's Avatar
kingbuzzo kingbuzzo is offline
Chief Ponti-yacker
 
Join Date: Mar 2022
Posts: 861
Default Am I missing something... 74 TA

Is there a trim piece between the lower valance and the front fender or do I need to mind the gap?

Seems like something should be there...
Click image for larger version

Name:	IMG_20240927_210949.jpg
Views:	115
Size:	33.3 KB
ID:	640613

Sent from my Surface Duo using Tapatalk

__________________
Esquire

'74 T/A 455 Y-code SD clone

previously on Dawson's Creek:

'74 T/A 400
'81 AMC SX/4
'69 FB 350
  #2  
Old 09-28-2024, 02:35 PM
nas t eh nas t eh is offline
Senior Chief
 
Join Date: Jun 2015
Location: Edmonton Alberta
Posts: 306
Default

There is no filler piece and there should be no gap.
The valance looks out of position( down and forward) of where it should be

__________________
73 T/A 455, 4speed

Last edited by nas t eh; 09-28-2024 at 02:46 PM.
  #3  
Old 09-28-2024, 04:05 PM
Held for Ransom's Avatar
Held for Ransom Held for Ransom is offline
Ultimate Warrior
 
Join Date: Mar 2000
Posts: 9,086
Default

Is your center spoiler there?
https://bringatrailer.com/listing/19...c-firebird-19/

__________________
So long, farewell.
  #4  
Old 09-28-2024, 05:33 PM
kingbuzzo's Avatar
kingbuzzo kingbuzzo is offline
Chief Ponti-yacker
 
Join Date: Mar 2022
Posts: 861
Default

I think so...

So I just need to loosen then move the valence some more or could the fender be out of whack on both sides?

ThanksClick image for larger version

Name:	IMG_20240928_163209.jpg
Views:	71
Size:	34.5 KB
ID:	640626Click image for larger version

Name:	IMG_20240928_103138.jpg
Views:	58
Size:	51.8 KB
ID:	640627

Sent from my Surface Duo using Tapatalk

__________________
Esquire

'74 T/A 455 Y-code SD clone

previously on Dawson's Creek:

'74 T/A 400
'81 AMC SX/4
'69 FB 350
  #5  
Old 09-29-2024, 10:50 AM
nas t eh nas t eh is offline
Senior Chief
 
Join Date: Jun 2015
Location: Edmonton Alberta
Posts: 306
Default

Yes, the easy thing to try, is loosen and move the ends of the valence.
After that, if there is still a gap.
Your bumper and header panel look to be tight to the fender so they are likely not the issue. Either the valence is out of position or it may have been damaged at some point. You may need to remove it and check where it is mounted to see if there is anything bent. Maybe the valence itself curves up in the center and hangs down at the ends.

__________________
73 T/A 455, 4speed
  #6  
Old 10-01-2024, 12:54 PM
kingbuzzo's Avatar
kingbuzzo kingbuzzo is offline
Chief Ponti-yacker
 
Join Date: Mar 2022
Posts: 861
Default

Is there an aftermarket valence available for this girl?

__________________
Esquire

'74 T/A 455 Y-code SD clone

previously on Dawson's Creek:

'74 T/A 400
'81 AMC SX/4
'69 FB 350
  #7  
Old 10-01-2024, 03:28 PM
pontiacstogo's Avatar
pontiacstogo pontiacstogo is offline
Chief Ponti-yacker
 
Join Date: May 2001
Location: Waihi, New Zealand
Posts: 533
Default

Ames do a fibreglass reproduction - no experience with it personally;

https://www.amesperf.com/parts/26293/

You should be able to close the gap up on yours and get it fitting tighter to the front fender - most of the adjustment relies on the bumper being aligned properly as the valance 'hangs' from the bumper.


__________________
Peter

1974 Trans Am, 400 4-speed, 3.42 rear.

  #8  
Old 10-01-2024, 05:27 PM
kingbuzzo's Avatar
kingbuzzo kingbuzzo is offline
Chief Ponti-yacker
 
Join Date: Mar 2022
Posts: 861
Default

Ohhhh ok...maybe it is the bumper

Thanks x2!

__________________
Esquire

'74 T/A 455 Y-code SD clone

previously on Dawson's Creek:

'74 T/A 400
'81 AMC SX/4
'69 FB 350
  #9  
Old 10-02-2024, 07:06 PM
1974-trans-am 1974-trans-am is offline
Junior Member
 
Join Date: Nov 2022
Posts: 9
Default

Had the same problem. The L shaped brackets that the bumper is attached to are attached to the frame horns on each side with two flair head and flair nuts that cinch into the sides of the frame when tightened. The frame horns have slotted holes to move fore and aft. I removed the valence and than you have access to these bolts as I remember? Also check the two bolts on each side that the bumper attaches to the brackets. Mine had been shimmed when what was needed was to adjust at the frame horn bolts.

  #10  
Old 10-03-2024, 12:12 PM
kingbuzzo's Avatar
kingbuzzo kingbuzzo is offline
Chief Ponti-yacker
 
Join Date: Mar 2022
Posts: 861
Default

Thanks sir...that is likely where I went wrong - I also may have finally found replacement bumpers so I need to open her up again anyways

__________________
Esquire

'74 T/A 455 Y-code SD clone

previously on Dawson's Creek:

'74 T/A 400
'81 AMC SX/4
'69 FB 350
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:43 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017