FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#1
|
||||
|
||||
![]()
1968 Pontiac Firebird Body Shell professionally Jig Built. Clear Missouri Title in my Name and PHS Documents for the car. Originally Cameo Ivory (white) with Red Interior and Console Automatic. PHS confirms that it’s original with a 350, 2BBL car so it’s actually nothing special. Extreme care was taken to remove every rusty panel on the car. We replaced every piece of sheet metal with exception of the inner roof structures, inner quarter panel bracing as shown in the sandblast photos. All panels were prepped with EDP removed to bare metal and weld-through primer at every weld seam. All inner structure has been cleaned and prepared with POR-15 rust inhibitors. All original structural parts were also treated with Ospho rust inhibitors prior to applying weld through primer and epoxy as needed. Car has been Mini Tubbed and can fit up to a 315 radial in the rear!
![]() All floor pan, trunk pan, wheelhouses and inner structure including inner/outer rocker and rocker mid braces are fully installed and welded in place. This is where I leave you to finish the job: Trunk drops are completely fitted, prepped and secured with screws. Ready to weld. New tail pan, full AMD premium quarters, sail panel, package tray and package tray braces are prepped and in place ready to weld. I have brand new AMD parts for installation and they have not been prepped for install but are new in boxes and included: Trunk Hinge Kit, quarter inner braces, seat braces, upper dash, cowl shoulders, upper cowl assembly to replace any rust found under the upper dash (factory is still installed but needs replacement). New doors and hinges are fitted and gapped I will include in this package a clean front subframe complete, fiberglass Glasstek front and rear bumpers, fuel neck filler parts new, new red headliner, a used gauge cluster and all new glass besides windshield Rear window glass is used. This stuff alone I have listed for over $1075. I have the car still on the Jig and it can be purchased to move the car for an additional $1000. You could recoup your money on it just by listing it on marketplace and selling it. Dynacorn gets over $22,000 for a new body shell and this is a fraction to f the price but you’ll need to finish welding it up. I have way too much going on these days to finish this project and this is an extremely nice car with well over this amount in sheet metal. No tire kickers this is firm on the price. I will not deliver it from Central Missouri so it must be picked up. I’ll sign over the title when you arrive with cash. More information and photos available upon request. Check out the build page at: https://www.facebook.com/share/15jRX...ibextid=wwXIfr ![]() I also had a build thread going under Street labeled Project Angry Bird. ![]() ![]() ![]() ![]() ![]() Call or text and if I don’t pick up, please leave me a message. Five seven three - 356 - zero three five five Located in Columbia Missouri 65202 which is central Missouri. $7500 Firm Sent from my iPhone using Tapatalk |
#2
|
||||
|
||||
![]()
Nice project car - for sure.
__________________
|
#3
|
|||
|
|||
![]()
Wish I could get my '69 done for that kind of money
![]()
__________________
"At no time did we exceed 175 mph.” Dan Gurney's truthful response to his and Brock Yate's winning of the first ever Cannonball Baker Sea-to-Shining Sea... Still have my 1st Firebird 7th Firebird 57 Starchief |
#4
|
||||
|
||||
![]() Yes we bought another house and need to move so unfortunately the car goes for super cheap. All that labor is free Sent from my iPhone using Tapatalk |
#5
|
||||
|
||||
![]()
I would lower the price to $5000 here. Hell of a deal for someone!
Sent from my iPhone using Tapatalk |
Reply |
Thread Tools | |
Display Modes | |
|
|