FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#1
|
||||
|
||||
26 spline input shaft For Clutch tool
I seem to have misplaced or loaned out my 26 spline input shaft I use on
Pressure Plate/Clutch Installations. Anyone have a 26 spline Input Shaft from a trans that I can buy for use as a clutch tool. Thanks Tom V.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
#2
|
||||
|
||||
Working on a deal to Borrow a Fine Spline Muncie Input Shaft but I am still interested in acquiring one for myself to use permanently.
Tom V.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
#3
|
|||
|
|||
Tom, are you against using one of the thick plastic 26 spline clutch disc line tools? Bought one years ago & it has worked well.
__________________
Buzzards gotta eat... same as worms. |
#4
|
||||
|
||||
"Years ago", parts might work if I can not find a proper input shaft to locate the disc properly for the installation. The chinese new stuff out there obviously is worthless.
I have a "possible" for the 26 spline input shaft to borrow locally. I will see if that works out first. Tom V. NEVER LOAN OUT YOUR TOOLS is typically a safe bet but I still do it occasionally.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
#5
|
|||
|
|||
The plastic tool is fine , remove it slide trans in & have someone depress the clutch pedal & you are done.
|
#6
|
|||
|
|||
They suck compared to a input shaft IMO!Tom
|
#7
|
|||
|
|||
|
#8
|
|||
|
|||
I’ve had good luck with the Ram tool; only about $50.
|
#9
|
||||
|
||||
X2 on the Ram alignment tool.
|
#10
|
|||
|
|||
For an idiot who is not positive what it looks like I have a box of transmission shafts and yokes. Happen to have a pic or dimensions?
|
#11
|
||||
|
||||
This
__________________
3 Generations of "Beach Boys Racing" ! Everybody knows somthin. Nobody knows everything ! 1st time on a dragstrip, 1964. Flagstart ! "Thanks for the entertainment." "Real Indians Don't Wear Bowties" |
#12
|
||||
|
||||
Quote:
https://www.superpages.com/bp/s-milw...2200051978.htm
__________________
3 Generations of "Beach Boys Racing" ! Everybody knows somthin. Nobody knows everything ! 1st time on a dragstrip, 1964. Flagstart ! "Thanks for the entertainment." "Real Indians Don't Wear Bowties" |
#13
|
|||
|
|||
No luck. The only one I have close is 22 spline
|
#14
|
||||
|
||||
Info from here: http://www.superchevy.com/how-to/tra...-transmissions
Input Shaft Identification Years Type Grooves Input Shaft Splines Output Tooth Count Output Shaft Splines 1963-’65 M20 None 10 24 27 1966-’70 M20 Two 10 21 27 1970-’74 M20 Two 26 21 32 1963-’70 M21 One 10 26 27 1970-’74 M21 One 26 26 32 1967-’70 M22 None 10 26 27 1969-’74 M22 None 26 26 32 So I am looking for a 26 spline input shaft for a 1970-1974 M20 Trans or a 1970-1974 M21 Trans, or a 1969-1974 M22 trans. The key is the 26 spline version vs the typical 10 spline GTO type Muncie Trans. Tom V.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
#15
|
|||
|
|||
'72 models were last factory installed M22's.
Input shaft from '2nd design BW T-10 (74 1/2 on) would also work.
__________________
Buzzards gotta eat... same as worms. |
Reply |
Thread Tools | |
Display Modes | |
|
|