Forum: Tri-Power Tech
07-23-2024, 01:09 PM
|
Replies: 4
Views: 592
Tri-Power setups obviously have three...
Tri-Power setups obviously have three needle/seats. Quadrajets have one. Holley's have two.
At full throttle, isn't it logical that the three fuel inlets allow more flow than any single carb? I...
|
Forum: 64-65 GTO Tempest & LeMans TECH
05-23-2024, 12:37 PM
|
Replies: 7
Views: 914
|
Forum: 64-65 GTO Tempest & LeMans TECH
03-22-2024, 04:49 PM
|
Replies: 97
Views: 67,099
|
Forum: THE LOBBY
02-14-2024, 01:41 PM
|
Replies: 70
Views: 5,945
Very disappointing. I believe most of us would...
Very disappointing. I believe most of us would much prefer an increase in dues rather than a digital magazine. This may be the beginning of the end of POCI. I'm 81 years old and have been a member...
|
Forum: 61-66 Big Pontiac TECH
01-19-2024, 05:29 PM
|
Replies: 2
Views: 891
Carter AFB
Whenever I restore an AFB, the screws, levers, and rods are bare steel. Can someone post a picture or describe to me what color they were plated when new?
I would like to do them correctly, rather...
|
Forum: Tri-Power Tech
12-22-2023, 05:18 PM
|
Replies: 5
Views: 1,749
|
Forum: Pontiac - Street
11-11-2023, 02:29 PM
|
Replies: 46
Views: 5,910
Yes, in the '60's, when most of our Pontiac...
Yes, in the '60's, when most of our Pontiac engines were produced, lifters were about $1.00 each. Cams were $25. We installed them and had very few failures, even with high valve spring pressures.
...
|
Forum: Tri-Power Tech
11-06-2023, 11:44 AM
|
Replies: 15
Views: 3,266
|
Forum: Tri-Power Tech
10-20-2023, 08:01 PM
|
Replies: 8
Views: 1,652
|
Forum: Pontiac - Street
10-08-2023, 12:57 PM
|
Replies: 8
Views: 1,052
|
Forum: Tri-Power Tech
07-27-2023, 12:24 AM
|
Replies: 17
Views: 2,454
|
Forum: 64-65 GTO Tempest & LeMans TECH
04-15-2023, 01:13 PM
|
Replies: 12
Views: 1,727
My father-in-law was an engineer at AO Smith in...
My father-in-law was an engineer at AO Smith in Milwaukee, where most GM frames were built until the 1970's. He said that the movement or twist on a typical automobile from one corner to the opposite...
|
Forum: Pontiac - Street
02-17-2023, 08:56 PM
|
Replies: 71
Views: 10,573
|
Forum: Tri-Power Tech
02-05-2023, 02:09 AM
|
Replies: 13
Views: 1,950
|
Forum: Pontiac - Street
01-20-2023, 06:24 PM
|
Replies: 42
Views: 5,872
|
Forum: Pontiac - Street
01-03-2023, 12:49 AM
|
Replies: 40
Views: 5,148
I agree with Tom V. I have not used liquid carb...
I agree with Tom V. I have not used liquid carb cleaner for many years. I have a blast cabinet and I use glass beads on carb bodies. This results in a shiny finish ready for dichromate finish just as...
|
Forum: THE LOBBY
12-23-2022, 05:55 PM
|
Replies: 72
Views: 8,825
|
Forum: Tri-Power Tech
12-16-2022, 05:16 PM
|
Replies: 51
Views: 22,262
|
Forum: Pontiac - Street
12-05-2022, 01:44 AM
|
Replies: 55
Views: 6,737
|
Forum: Pontiac - Street
12-03-2022, 12:53 AM
|
Replies: 55
Views: 6,737
|
Forum: Pontiac - Street
11-02-2022, 11:19 AM
|
Replies: 56
Views: 11,621
|
Forum: National Events
08-16-2022, 12:51 AM
|
Replies: 55
Views: 19,237
|
Forum: 64-65 GTO Tempest & LeMans TECH
04-27-2022, 10:07 AM
|
Replies: 15
Views: 2,562
|
Forum: Tri-Power Tech
02-19-2022, 11:15 AM
|
Replies: 32
Views: 10,903
|
Forum: 64-65 GTO Tempest & LeMans TECH
01-05-2022, 09:24 PM
|
Replies: 97
Views: 67,099
|