Forum: Pontiac - Street
Today, 11:33 AM
|
Replies: 9
Views: 204
|
Forum: Pontiac - Street
06-21-2024, 10:22 AM
|
Replies: 25
Views: 729
|
Forum: Pontiac - Street
06-07-2024, 04:04 PM
|
Replies: 16
Views: 848
|
Forum: Pontiac - Street
06-05-2024, 09:28 AM
|
Replies: 18
Views: 430
|
Forum: Pontiac - Street
05-31-2024, 04:10 PM
|
Replies: 26
Views: 982
That seals OD coating is likely to dry out and...
That seals OD coating is likely to dry out and cause a issue before the actual crank seal lip does..
Get a good seal with a metal OD and just put it in with some gray form-A- gasket and then sleep...
|
Forum: THE LOBBY
05-21-2024, 02:12 AM
|
Replies: 20
Views: 1,051
|
Forum: Pontiac - Street
05-16-2024, 01:23 PM
|
Replies: 16
Views: 450
This is nonsense.
A lot of factory cars...
This is nonsense.
A lot of factory cars had manual disc in the 60's till the mid 70's; Corvettes, Camaros, Firebirds, and especially Mustangs. I have hands-on converted several vehicles to...
|
Forum: Pontiac - Street
05-03-2024, 09:51 AM
|
Replies: 19
Views: 855
|
Forum: Pontiac - Street
04-23-2024, 06:29 AM
|
Replies: 64
Views: 3,663
|
Forum: Pontiac - Street
04-19-2024, 10:23 PM
|
Replies: 43
Views: 2,916
I have had unilites in my birds forever. They...
I have had unilites in my birds forever. They used to say they were unreliable so I bought an extra module it’s been in my electrical tool box since the early 90s ! So pretty reliable from my...
|
Forum: Pontiac - Street
04-03-2024, 10:42 AM
|
Replies: 21
Views: 1,391
If the car is being autocrossed, I would...
If the car is being autocrossed, I would absolutely go with the 4" stroke. You'll be able to manage off corner acceleration a bit easier without the grunt the added stroke is going to give you at...
|
Forum: THE LOBBY
03-21-2024, 07:17 PM
|
Replies: 47
Views: 2,090
|
Forum: THE LOBBY
03-14-2024, 03:14 PM
|
Replies: 4
Views: 636
|
Forum: Pontiac - Street
02-20-2024, 06:18 PM
|
Replies: 21
Views: 1,561
|
Forum: Pontiac - Street
02-14-2024, 01:39 PM
|
Replies: 81
Views: 5,989
|
Forum: Pontiac - Street
02-10-2024, 11:12 AM
|
Replies: 99
Views: 6,314
Wix 51258 Discontinued
As the title says, According to summit, so I assume the Napa gold 1258 is also, as well as the Wix 51042 A freind of mine was running that one with Hedman headers not sure what a guy is gonna do now.
|
Forum: Pontiac - Street
01-28-2024, 11:09 AM
|
Replies: 64
Views: 3,776
|
Forum: THE LOBBY
01-25-2024, 05:55 PM
|
Replies: 156
Views: 10,042
|
Forum: THE LOBBY
01-24-2024, 10:51 PM
|
Replies: 156
Views: 10,042
|
Forum: Pontiac - Street
01-20-2024, 07:28 PM
|
Replies: 84
Views: 7,171
|
Forum: Pontiac - Street
01-20-2024, 11:47 AM
|
Replies: 10
Views: 1,099
There was a long post about this running last...
There was a long post about this running last month and to sum up what was covered it came down to run a factory cast crank or bust out the added green for a aftermarket steel crank.
Not many...
|
Forum: Pontiac - Street
01-20-2024, 11:46 AM
|
Replies: 10
Views: 1,099
Pontiac V-8's are often referred to as "middle...
Pontiac V-8's are often referred to as "middle blocks" 383 Chrysler engines are also referred to in that way. 287-455 cubic inches covers allot of ground. Eagle stating some HP numbers for their...
|
Forum: Pontiac - Street
01-19-2024, 07:54 PM
|
Replies: 84
Views: 7,171
I have been running my 455's @ 600-650HP and...
I have been running my 455's @ 600-650HP and 275-325 shot of nitros
for years and the factory N cranks have held up fine, Thats over-under
A 1000HP so I wouldn't be afraid to run a factory crank at...
|
Forum: Pontiac - Street
01-19-2024, 04:35 PM
|
Replies: 84
Views: 7,171
Certainly a light rotating assembly is a help. ...
Certainly a light rotating assembly is a help. We did this out of necessity and budget. No aftermarket forgings were available, only an old 990 crank if you could find one. Billet crankshafts were...
|
Forum: Pontiac - Street
01-19-2024, 12:57 PM
|
Replies: 84
Views: 7,171
I would leave the N crank in it if it’s looking...
I would leave the N crank in it if it’s looking as good as you say.
That crank is more than adequate for what you’re doing, with a lighter set of rods and pistons it’ll be even better than before....
|