Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Showing results 1 to 13 of 13
Search took 0.01 seconds. Search: Posts Made By: TB1
Forum: Pontiac - Street 09-10-2023, 10:57 AM
Replies: 40
Views: 2,191
Posted By TB1
If you want to get it down without waiting for...

If you want to get it down without waiting for parts or tools to arrive, get a telescopic magnet and a 3/8 x 1.25 NC bolt and nut and lock washer drill out the hole in the frame and install, This is...
Forum: Pontiac - Street 09-01-2023, 08:07 PM
Replies: 20
Views: 1,357
Posted By TB1
And we have a winner! I ran into the same...

And we have a winner! I ran into the same issue with my car's PS belt, I have CFV billet pulleys installed and once I sourced the wider belts no more issues. Mine would squeal at high rpm only but...
Forum: Pontiac - Street 03-30-2023, 09:45 PM
Replies: 1,977
Views: 261,544
Posted By TB1
ya what Singleton said, how do we go from a leak...

ya what Singleton said, how do we go from a leak on an oil filter adapter to the crankcase full of water from a timing cover gasket leak, then to "There was only a small leak at the thermostat...
Forum: Pontiac - Street 08-14-2022, 11:24 AM
Replies: 1,977
Views: 261,544
Posted By TB1
Try a wider belt, The length may not be your...

Try a wider belt, The length may not be your issue at all, I have the same pullies without AC and am using factory brackets and had some belt squeal with the PS pump. I did some research and...
Forum: Pontiac - Street 08-11-2022, 06:44 PM
Replies: 22
Views: 1,707
Posted By TB1
I have never driven a car with a TKO but the TKX...

I have never driven a car with a TKO but the TKX in my car and the T56 in my buddies 65 GTO both shift super smooth. When I was reading up on the TKX before purchasing it was stated that they had...
Forum: Pontiac - Street 07-24-2022, 11:12 AM
Replies: 6
Views: 1,185
Posted By TB1
Between the column and the steering box you...

Between the column and the steering box you should have an intermediate shaft of some sort with slip collars held in place with set screws that can be moved/removed to allow the shaft to come out and...
Forum: Pontiac - Street 04-20-2022, 12:58 AM
Replies: 18
Views: 1,962
Posted By TB1
Yes you can shim the bellhousing for parallel run...

Yes you can shim the bellhousing for parallel run out,I had to do this to install my TKX, But first the radial run out needs to be taken care of either with offset dowel pins or if your lucky the...
Forum: Performance Parts For Sale/Wanted 02-10-2022, 11:48 AM
Replies: 12
Views: 1,206
Posted By TB1
Still available just waiting to get in contact...

Still available just waiting to get in contact with 61-63, will follow up later today
Forum: Pontiac - Street 04-15-2021, 08:19 PM
Replies: 47
Views: 7,140
Posted By TB1
Bit of an update after checking and adjusting the...

Bit of an update after checking and adjusting the pinion angle and using the Tremec app I had the the driveline angles dialed in, took the car for another drive on the hwy at 70+ mph same issue bad...
Forum: Pontiac - Street 03-01-2021, 12:23 PM
Replies: 23
Views: 4,276
Posted By TB1
The GM version has three OD ratios depending on...

The GM version has three OD ratios depending on close or wide ratio. The wide ratio is a 3.27 1st gear which has the 0.72 OD , The close ratio both have 2.87 1st gear but the OD can either be a .68...
Forum: Pontiac - Street 02-22-2021, 01:30 AM
Replies: 47
Views: 7,140
Posted By TB1
The factory crossmember was used and only...

The factory crossmember was used and only required a small amount of cutting to clear.
...
Forum: Performance Parts For Sale/Wanted 01-05-2021, 10:37 AM
Replies: 12
Views: 1,159
Posted By TB1
found in another thread, I have swapped some carb...

found in another thread, I have swapped some carb parts with him in the past and all went well.

http://forums.maxperformanceinc.com/forums/showthread.php?t=837495
Forum: Pontiac - Street 05-20-2020, 12:42 AM
Replies: 34
Views: 2,079
Posted By TB1
Lots of good info given below on the proper set...

Lots of good info given below on the proper set up. I was just looking at this picture you posted before the z bar in the pic circled in black [if that’s what it is] does not look like the factory 64...
Showing results 1 to 13 of 13

 
Forum Jump

All times are GMT -4. The time now is 01:12 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017