Forum: 68-69 GTO Tempest & LeMans TECH
04-16-2024, 07:24 PM
|
Replies: 14
Views: 452
|
Forum: 68-69 GTO Tempest & LeMans TECH
04-14-2024, 01:14 PM
|
Replies: 14
Views: 452
|
Forum: 68-69 GTO Tempest & LeMans TECH
04-12-2024, 10:31 PM
|
Replies: 14
Views: 452
|
Forum: 68-69 GTO Tempest & LeMans TECH
04-12-2024, 08:24 PM
|
Replies: 14
Views: 452
|
Forum: 68-69 GTO Tempest & LeMans TECH
04-12-2024, 06:13 PM
|
Replies: 14
Views: 452
Nice work!
When I pulled off the factory...
Nice work!
When I pulled off the factory wood grain of my 68 Lemans parts car it had a thin steel sheet beneath it, very nice backing for the vinyl but it was rusted on the back and I didn't use...
|
Forum: 68-69 GTO Tempest & LeMans TECH
04-12-2024, 05:06 PM
|
Replies: 14
Views: 452
|
Forum: Pontiac - Street
04-01-2024, 12:21 PM
|
Replies: 15
Views: 680
Crank it until it starts.
Don’t crank it so...
Crank it until it starts.
Don’t crank it so long that you overheat the starter, do it in a few steps.
What’s the big deal, it’s only been a few months and nothing special needs to be done.
...
|
Forum: THE LOBBY
03-30-2024, 11:31 AM
|
Replies: 32
Views: 1,220
|
Forum: 68-69 GTO Tempest & LeMans TECH
03-30-2024, 11:25 AM
|
Replies: 13
Views: 667
|
Forum: THE LOBBY
03-30-2024, 08:12 AM
|
Replies: 32
Views: 1,220
The cover is just going to cause issues and...
The cover is just going to cause issues and you’ll be worried about what is happening under the cover the whole trip.. It will obviously make people even more curious to what’s underneath and really...
|
Forum: The Body Shop TECH
03-23-2024, 08:10 AM
|
Replies: 2
Views: 364
Epoxy primer is the answer. At my shop we...
Epoxy primer is the answer. At my shop we encounter lead on almost everything we restore. Because the lead sometimes has open air pockets/pin holes we don't use any chemical paint strippers or acids...
|
Forum: THE LOBBY
03-21-2024, 11:51 AM
|
Replies: 13
Views: 1,055
LeMans on a Wallet
Anyone else here make stuff out of leather?
I occasionally assemble Tandy leather kits and attempt tooling.
I found I can take a photo, run it through an app that creates an outline, and use it...
|
Forum: 68-69 GTO Tempest & LeMans TECH
03-06-2024, 04:11 PM
|
Replies: 15
Views: 863
|
Forum: THE LOBBY
03-02-2024, 04:00 PM
|
Replies: 26
Views: 1,191
|
Forum: The Body Shop TECH
02-24-2024, 07:51 PM
|
Replies: 7
Views: 522
|
Forum: The Body Shop TECH
02-19-2024, 11:27 AM
|
Replies: 4
Views: 594
Bumper repair If youre brave
Dont know why my 67 rotted like this
there was no debris stuck between the reinforcement bar and bumper.
I cut out just short of any lines as to keep the lines intact.
Some areas near the cuts...
|
Forum: Suspension TECH
02-15-2024, 12:58 PM
|
Replies: 60
Views: 2,287
|
Forum: THE LOBBY
02-07-2024, 09:36 AM
|
Replies: 53
Views: 1,755
|
Forum: THE LOBBY
02-07-2024, 09:16 AM
|
Replies: 53
Views: 1,755
i had to replace my Ipad 2 with Ipad 4, then...
i had to replace my Ipad 2 with Ipad 4, then again (forget what this Pad is) but every time it was because certain Site would not react with speed, forget my User ID,or even load the Site at all. The...
|
Forum: THE LOBBY
02-06-2024, 10:31 PM
|
Replies: 53
Views: 1,755
|
Forum: The Body Shop TECH
01-11-2024, 04:50 AM
|
Replies: 27
Views: 1,739
|
Forum: The Body Shop TECH
01-10-2024, 10:27 PM
|
Replies: 27
Views: 1,739
No, the twin tube is 05887, the product Bruce...
No, the twin tube is 05887, the product Bruce showed.
05895 was the 5 oz tubes. Still available online from a few sellers
05896 was the 13 oz tubes, discontinued some time ago.
05887 is the...
|
Forum: 68-69 GTO Tempest & LeMans TECH
01-08-2024, 06:10 AM
|
Replies: 109
Views: 7,651
|
Forum: THE LOBBY
12-31-2023, 03:39 PM
|
Replies: 6
Views: 484
Happy New Year
Another year comes to an end. Some of us didn’t make as much progress on our projects as we had hoped but tomorrow starts a new year to accomplish more.
Let’s remember those who are not here...
|
Forum: Exhaust TECH
12-13-2023, 08:51 PM
|
Replies: 29
Views: 4,553
How mine looked after 30k miles and 5 years of...
How mine looked after 30k miles and 5 years of daily driver use, my first attempt at using POR-15 manifold paint about 24 years ago.
I did use Metal Prep after bead blasting them to clean and etch...
|