Forum: Pontiac - Street
04-07-2024, 07:22 AM
|
Replies: 6
Views: 353
Dakota Digital
I think I posted a while back about my gas gauge quitting working and assuming it was the sending unit (Tanks Inc. Floatless Unit). Well ever since I have had these Dakota Digital RTX gauges there...
|
Forum: Pontiac - Street
03-17-2024, 03:30 PM
|
Replies: 1,977
Views: 261,938
|
Forum: Pontiac - Street
03-16-2024, 12:57 PM
|
Replies: 1,977
Views: 261,938
Man this has been a blast and considering the...
Man this has been a blast and considering the headliner and back quarter boards aren’t done I didn’t expect this kind of reception. I am tired of talking to people though LOL. I had two people ask me...
|
Forum: Pontiac - Street
03-15-2024, 07:56 PM
|
Replies: 1,977
Views: 261,938
|
Forum: Pontiac - Street
03-15-2024, 06:33 AM
|
Replies: 1,977
Views: 261,938
|
Forum: Pontiac - Street
03-14-2024, 08:54 PM
|
Replies: 1,977
Views: 261,938
|
Forum: Pontiac - Street
03-13-2024, 07:04 PM
|
Replies: 1,977
Views: 261,938
|
Forum: Pontiac - Street
03-09-2024, 04:52 PM
|
Replies: 1,977
Views: 261,938
|
Forum: Pontiac - Street
03-08-2024, 05:10 PM
|
Replies: 1,977
Views: 261,938
Well next Thursday I’m gonna make a 500 mile...
Well next Thursday I’m gonna make a 500 mile round trip drive to the Run to the Sun car show in Myrtle Beach. After I get back (18th) I will be taking my car to a local carb shop to have the carb...
|
Forum: Pontiac - Street
03-01-2024, 11:00 AM
|
Replies: 78
Views: 4,066
Just an update to this. The MSD 6AL AND the...
Just an update to this. The MSD 6AL AND the distributor were bad. I sent the box in for evaluation and the replaced a diode and capacitor. Sent it back and I rechecked all the wire, it was good so I...
|
Forum: Pontiac - Street
02-06-2024, 08:39 PM
|
Replies: 98
Views: 4,339
|
Forum: Pontiac - Street
01-28-2024, 01:28 AM
|
Replies: 46
Views: 3,459
I am not sure what your engine combo is but on...
I am not sure what your engine combo is but on the old ass o meter from the roller cam I replaced with the 60919 HFT I can tell no difference in performance. Great cam if it’s a fit for your combo
|
Forum: Pontiac - Street
01-27-2024, 10:10 AM
|
Replies: 46
Views: 3,459
|
Forum: Pontiac - Street
01-26-2024, 06:16 PM
|
Replies: 46
Views: 3,459
|
Forum: Pontiac - Street
01-26-2024, 04:47 PM
|
Replies: 46
Views: 3,459
I didn’t give much information with my post. We...
I didn’t give much information with my post. We used ton of assembly lube and moly. Lucas 30 break in oil WITH a bottle of Lucas ZDDP. I changed the oil immediately, ran another change of break in...
|
Forum: Pontiac - Street
01-26-2024, 09:07 AM
|
Replies: 46
Views: 3,459
|
Forum: Pontiac - Street
01-17-2024, 05:18 PM
|
Replies: 161
Views: 8,290
|
Forum: Pontiac - Street
12-30-2023, 05:20 PM
|
Replies: 111
Views: 5,324
|
Forum: Pontiac - Street
12-30-2023, 10:08 AM
|
Replies: 5
Views: 694
|
Forum: Pontiac - Street
12-27-2023, 05:31 PM
|
Replies: 111
Views: 5,324
|
Forum: Pontiac - Street
12-17-2023, 03:27 PM
|
Replies: 19
Views: 2,598
Unless this is a concourse resto get a roll of ...
Unless this is a concourse resto get a roll of aluminum fuel line, hook a coat hanger to it with duct tape to pull it thru the front frame horn and line up with the fuel pump inlet. Unroll the rest...
|
Forum: Pontiac - Street
12-09-2023, 01:59 PM
|
Replies: 1,977
Views: 261,938
|
Forum: Pontiac - Street
12-02-2023, 06:45 PM
|
Replies: 9
Views: 511
I’m sure there is a joke about me and my posts...
I’m sure there is a joke about me and my posts coming so I’ll head it off. My build thread has had some great discourse and information in it. I am proud of that car and a lot of it was done from...
|
Forum: Pontiac - Street
11-15-2023, 04:17 AM
|
Replies: 40
Views: 2,209
Local Jeep fab shop drilled out the holes one...
Local Jeep fab shop drilled out the holes one size bigger, dropped bolts down thru the frame and tacked the bolts in place for 15 bucks. Now I have sway bar studs LOL. Just gotta put it back on
|
Forum: Pontiac - Street
11-05-2023, 07:31 AM
|
Replies: 1,977
Views: 261,938
Well I’m getting close to the end of the major...
Well I’m getting close to the end of the major work. If my wife feels like it today we will be putting carpet in and then I will have to set aside some money to get someone to do the headliner but...
|