Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Page 1 of 6 1 23 Last »
Showing results 1 to 25 of 134
Search took 0.07 seconds. Search: Posts Made By: AG
Forum: Pontiac - Street 04-05-2024, 11:11 AM
Replies: 36
Views: 1,024
Posted By AG
I put a light coat of paint on my BHJ balancer...

I put a light coat of paint on my BHJ balancer before I had my rotating assembly balanced to prevent rust formation and there is no rust after 10 years. I also painted my reluctor wheel in my MSD...
Forum: Pontiac - Street 03-23-2024, 10:20 PM
Replies: 58
Views: 2,271
Posted By AG
It was a clients car and he has the directions. ...

It was a clients car and he has the directions. I don't remember exactly how I adjusted them but I think I used at least a full turn.
Forum: Pontiac - Street 03-10-2024, 08:05 PM
Replies: 39
Views: 1,963
Posted By AG
My race car has 0.0029"-0.0035" main clearances...

My race car has 0.0029"-0.0035" main clearances and 0.0024-0.0026" rod clearances. I use Walmart 10W-40 full syn and it has 30 psi at full heat soaked 1000 rpm idle. I have had it apart and all the...
Forum: Pontiac - Street 02-28-2024, 08:10 PM
Replies: 70
Views: 6,417
Posted By AG
i8 is the best.

i8 is the best.
Forum: Pontiac - Race 02-24-2024, 09:31 PM
Replies: 22
Views: 1,367
Posted By AG
My old bathtub Eddy chambers work best at 39...

My old bathtub Eddy chambers work best at 39 degrees timing for best mph.
Forum: Pontiac - Race 02-24-2024, 09:27 PM
Replies: 24
Views: 1,480
Posted By AG
I always do that since it's easy and free.

I always do that since it's easy and free.
Forum: Pontiac - Street 02-01-2024, 09:38 PM
Replies: 57
Views: 4,369
Posted By AG
I had it in a 1965 LeMans. I got severe...

I had it in a 1965 LeMans. I got severe wheel-hop off the line and didn't get out of it soon enough. The carrier and axles stayed in but the whole front of the housing/pinion support blew apart.
Forum: Pontiac - Street 02-01-2024, 07:33 PM
Replies: 57
Views: 4,369
Posted By AG
I have a 1971 8.2 out of a GP with a 3.07 4...

I have a 1971 8.2 out of a GP with a 3.07 4 pinion STT.
Forum: Pontiac - Street 01-29-2024, 10:12 PM
Replies: 19
Views: 1,123
Posted By AG
Less parasitic loss compared to a 9" and it's...

Less parasitic loss compared to a 9" and it's lighter, not sure about a Dana 60.
Forum: Pontiac - Street 01-25-2024, 08:16 PM
Replies: 46
Views: 3,317
Posted By AG
I installed a used RA IV cam using used HFT...

I installed a used RA IV cam using used HFT lifters in the fall of 2022 and everything worked no problem. I used 100# seat pressure CC cam lube on the cam and moly paste on the bottom of the...
Forum: Pontiac - Street 01-21-2024, 05:19 PM
Replies: 19
Views: 1,105
Posted By AG
You can get the rod bearings coated to tighten up...

You can get the rod bearings coated to tighten up the clearance. I used Calico with great success, I coat all my bearings now.
Forum: Suspension TECH 01-20-2024, 09:13 PM
Replies: 41
Views: 2,389
Posted By AG
I put a Wilwwod 1" master and proportioning valve...

I put a Wilwwod 1" master and proportioning valve on my brother's 1970 LeMans with GM front disc/ rear drum and it works great and doesn't pollute the engine bay. I called Willwood to get their...
Forum: Pontiac - Street 01-18-2024, 12:48 PM
Replies: 158
Views: 7,502
Posted By AG
I have an 8.9:1 CR 462 with a RAIV cam and Rhoads...

I have an 8.9:1 CR 462 with a RAIV cam and Rhoads lifters in my '72 convertible with RA manifolds, 7K3 heads, an HO intake and Qjet. I think it's a great combination and has very good street manners...
Forum: Pontiac - Street 01-15-2024, 09:03 PM
Replies: 39
Views: 2,335
Posted By AG
https://www.summitracing.com/parts/crt-m6907/make/...

https://www.summitracing.com/parts/crt-m6907/make/pontiac
Forum: Pontiac - Street 01-10-2024, 08:29 AM
Replies: 16
Views: 1,450
Posted By AG
The Victor intake will not fit under your stock...

The Victor intake will not fit under your stock hood unless you don't run an air cleaner. You will need to get a cowl hood or some type of scoop.
Forum: Pontiac - Street 01-03-2024, 11:53 AM
Replies: 44
Views: 1,913
Posted By AG
I used a set of CC HR Evolution lifters to...

I used a set of CC HR Evolution lifters to replace a set of Lunati HR lifters and was very impressed with them. All the plungers moved freely, adjusted easily and were completely quiet from the...
Forum: Pontiac - Street 12-12-2023, 08:17 AM
Replies: 22
Views: 1,287
Posted By AG
My LeMans has the same problem. I have the stock...

My LeMans has the same problem. I have the stock 3 core radiator and run a 8.9:1 455 with a 180 T-stat and a Flex-a-lite 7 blade 19" fan. I was using a 160 Tstat and on a 90+F day it would only get...
Forum: Pontiac - Street 12-01-2023, 10:39 PM
Replies: 25
Views: 1,585
Posted By AG
I put the cam in post #14 in a customers 1971...

I put the cam in post #14 in a customers 1971 455HO car with stock compression and it runs very well. I think it would run well in a 433 with a higher CR but I would use the larger one in your motor.
Forum: Pontiac - Street 11-28-2023, 10:46 AM
Replies: 57
Views: 10,367
Posted By AG
The non-CNC ported complete heads were only about...

The non-CNC ported complete heads were only about $1150 and even after watching the videos about the assessments of the heads I would still buy them for a budget motor and clean up the ports. It...
Forum: Pontiac - Street 11-20-2023, 09:03 PM
Replies: 23
Views: 1,498
Posted By AG
Your 4 pinion posi is a cone type, not a clutch...

Your 4 pinion posi is a cone type, not a clutch type that you can replace the clutches. You can get an Eaton clutch type posi for the 10 bolt, but they are expensive. If you have the money I'd get...
Forum: Pontiac - Race 11-15-2023, 02:41 PM
Replies: 13
Views: 944
Posted By AG
I run a 3.90 gear and changing from a 29" tire to...

I run a 3.90 gear and changing from a 29" tire to a 28" tire had no effect on ET. I can't remember if there was any difference in rpm going across the line, but there was no change in converter...
Forum: Pontiac - Street 11-02-2023, 09:30 AM
Replies: 12
Views: 550
Posted By AG
I ran a 11.5x15x28 tire on an 8" rim and it...

I ran a 11.5x15x28 tire on an 8" rim and it needed a 5" BS in my '65 LeMans.
Forum: Pontiac - Street 10-20-2023, 06:40 PM
Replies: 50
Views: 1,751
Posted By AG
I'd rather have that one.

I'd rather have that one.
Forum: Pontiac - Race 10-13-2023, 11:15 PM
Replies: 20
Views: 1,108
Posted By AG
I had to use one 0.060" and one 0.120" gasket...

I had to use one 0.060" and one 0.120" gasket from Butler with my Victor/Dominator to get good port alignment. They only needed a small amount of trimming to fit well.
Forum: Pontiac - Race 10-06-2023, 08:45 PM
Replies: 16
Views: 831
Posted By AG
I ran a 455 at 11.4:1 static CR with stock 16...

I ran a 455 at 11.4:1 static CR with stock 16 D-ports and an Ultradyne 255/263 duration @0.050" solid flat tappet and the car went 11.4 in the 1/4 as a point of reference.
Showing results 1 to 25 of 134
Page 1 of 6 1 23 Last »

 
Forum Jump

All times are GMT -4. The time now is 01:43 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017