Built 462 with wideports
 

455 two bolt main with ARP studs
Just Block filled to lower water holes
New Lifter bore brace
Pontiac “N” Crank Fresh from Machine shop
ATI Balancer
SFI Flywheel with Arp bolts
New Eagle H-beam rods
New SRP .030 over pistons
Bottom end balanced and assembled by Jack Gaydosh
Custom Deep oil pan
Factory Windage Tray
New Melling Oil pump
Cometic Head Gaskets
New Cloyes Timing Chain
Solid roller Cam, with offset Crower lifters .440 lobe Degreed by Gaydosh
New Manley pushrods
Edelbrock Wideports 360ish @700 65cc Chambers (fresh, with new springs)
T&D Shaft rocker
Custom ARP Head studs to clear T&D shafts
Ported Victor (Port matched and clean up)
New Mezier Water pump
Moroso Vacuum pump
Custom Alternator Mount with Power master 1 wire Alternator
New Billet Crank mandrel drive
MSD Crank Trigger
Almost every bolt on the motor is ARP
Fabricated Aluminum Valve covers (Gaydosh Performance with “The Monster” script written on them)
Never fired, still on engine stand. Have not bolted on the T&Ds so there is on pressure on springs. Need to finish installing T&D’s, install intake and prime and fire.
10500 OBO parts negotiable

Pic
 

Another pic

Will consider selling top ends seperatly

I have some interest in the heads. However, everything is still available.

What is the compression?


Sent from my iPhone using Tapatalk

It's around 13.5:1

Bump

Sent you a PM. Let me know if you want to sell some of the accessories.

I won't separate it until someone wants the heads, or bottom end.

Price dropped 1000.00
Now its yours for 9500.00!

I will separate the Heads.
These are KRE wideports that were advertised at 350 to 365 cfm
65cc Chambers
4500.00 with Intake and T&D rocker Shafts

Flow sheet
 

Here is the original flow sheet on the heads.

Great xmas gift to yourself! Lol

May drop the price if someone wants to spit it up and not buy the accessories with it!

Bump

3800.00 for Wideports, T&D shaft rockers, lifters and intake
Plus Shipping Final deal on heads

Are the heads/ intake still available?

heads
 

are they available

Sorry. Wish I would have known last week. I bought a set from another member. Would have loved to have wide ports. Great deal with the rockers.

They are available. I have someone interested in complete engine, but no money in my hand as of yet!

Price for the short block?

Depends on what accessories you want with it, but around 4000.00 as shown without top end

heads
 

am interested in heads and t + d number I can reach you thk u

I would only need the balancer and flex plate.

Call me
301-606-2695

Month bump

Heads, Intake, shaft rockers and lifters are sold.

is the crank trigger for sale?

Thanks,
Tom

Not yet Tom. I have to wait for final sale of block.

Heads and top end may be available again!! Sale pending.......
If interested call me.
301-606-2695

I'm still curious as to the short block price. I tried to call a couple times.

$4200.00

Short block available

UP for sale again
 

Looks like the heads are up for sale!
Sent them to Kauffman for him to look over, he said all is good.
New PAC springs, flow 360 cfm as the flow sheet states
Fresh from the machine shop ready to bolt on and go.
Key feature... they are Dry Decked!
Also, point out so all is open to see that there is one pushrod tube that was epoxied when these were built. Have been ran on a car with NO issues.

pics
 

Attachment 433349

Attachment 433350

Attachment 433351

Attachment 433352

Attachment 433353

Short Block
 

Pics of short block

Stillllllllllllllllllllllllllllllllllllllll
available
This is a killer deal!

Bump
Just wow

Now, I'm just going for the most views record....

PM Sent

Sold! Thanks PY

Is the whole motor still available. 9500 buys it..

My bad
.sr.. moment

Motor is sold! New buyer added heads.... motor made 698 hp and 630 ft lbs of torque
Good job Jack Gaydosh!!