PY Online Forums - Bringing the Pontiac Hobby Together

PY Online Forums - Bringing the Pontiac Hobby Together (https://forums.maxperformanceinc.com/forums/index.php)
-   70-72 GTO Tempest & LeMans TECH (https://forums.maxperformanceinc.com/forums/forumdisplay.php?f=436)
-   -   chasis ground (https://forums.maxperformanceinc.com/forums/showthread.php?t=484663)

Aaron75 07-11-2006 12:27 PM

chasis ground
 
Could anybody send me or post shots of where the chasis ground is connected to the engine block or the battery?

I recently had my engine compartment wires replaced and ever since the gagues haven't been grounded properly. I'm thinking there's probably supposed to be some wire that grounds the engine and chasis as the ground for the battery is only connected to the block.

Thanks for the help.

Aaron

70KGOLD 07-11-2006 06:20 PM

What car do you want?

Aaron75 07-11-2006 06:40 PM

gack!!
 
sheesh i'm not all that swift today am I.

Sorry, its a '70 gto (455) but i'm sure that part doesn't matter.

Thanks.

Aaron

70KGOLD 07-11-2006 08:11 PM

Yes it matters. On my 1970 GTO The ground from the battery goes to a head bolt. Then I have a ground connected to the rear of the engine (on the head) to the (Firewall) its a flat copper strap. You can never have enough ground.

gtoformula 07-11-2006 10:00 PM

I have a 1970 GTO hardtop with a 400, auto trans. There is also a ground strap that runs from the front passenger side frame rail (a bit back from the radiator) to the passenger side inner fender.

Aaron75 07-12-2006 12:28 PM

Thanks guys
 
I agree, one can never have enough ground, especially when my guages like to blink w/ my turn signal. Nice!!

How are the copper straps attached? I am at a loss here as I've no experience w/ how things were done back in the day and I had someone else pull my engine. This means i couldn't 'put things back the way they were'.

It would be great if i could get a shot or two. If you don't have a place to post it, i'd be super greatful if you could forward it to my email.

Thanks again guys.

Aaron

Bob70Goat 07-13-2006 08:58 PM

sounds like there maybe a bad round on the printed circuit board for the gauges

Aaron75 07-19-2006 05:42 PM

ok, no pix
 
can i get a bit more description regarding the correct location?

I've got this image... http://ultimategto.com/1970/70_00083_11.jpg showing the ground at the fire wall. When you say connecting to the head, do you mean the support for spark plug wires? Is there another location where it should be?

I see a whole on the front passanger side frame rail, but i cannot find a whole on the inner fender would it be up around the washer fluid container?

Thanks guys.

Aaron

johnta1 07-19-2006 06:08 PM

That pic has the ground wire attached to one of the accessory holes on the back of the head.

Aaron75 07-19-2006 06:39 PM

hmm
 
that seems to be a reoccuring theme amongst some of the '70 engine compartments that i've been looking at. This isn't the correct location?


i've noticed a bunch of early goat owners seem to think it should go on the driver's side, not the passengers.

Aaron

Held for Ransom 07-20-2006 08:49 PM

3 Attachment(s)
Per the GTO assembly manual...

And, one of my cars (firewall is stripped, but it was attached to the lower hole but I believe it should have been the circled hole) I will look for the strap and see if I can get another picture of the mounting.

Held for Ransom 07-23-2006 10:57 PM

4 Attachment(s)
Aaron75, was your GTO built in Fremont (Z in the VIN)? Sometime in Feb. or Mar. it looks like the Fremont plant changed the location of the strap on the firewall (may have been earlier at other plants), to under the voltage regulator. I've also included pictures of the mounting location on the head, the components used and, at some point, they added an extra ground to the wiring harness.

Aaron75 07-24-2006 10:59 AM

yes it was
 
thanks so much!! It was made in fremont. These shots are perfect. Looks like i stuck it in the wrong spot but i'll definatel make the change.

Is this the only strap, or do i have to worry about the frame to passenger inner fender (can't find those holes either).

Aaron

Held for Ransom 07-24-2006 05:43 PM

I'm not going to say some plants didn't install them, but I've never seen them there. And the assembly manual doesn't mention it either. Do I have your trim tag info entered into my database? PM me, please.

Aaron75 07-24-2006 06:48 PM

you don't have the info...
 
PM you?

where would i find the trim tag info?

Aaron

Aaron75 07-24-2006 06:56 PM

nevermind
 
about the pm i figured that out. Where do i get the trim tag info?

Aaron

Held for Ransom 07-24-2006 10:52 PM

The trim tag (or body tag) is a stamped metal plate and is located under the hood, near the master cylinder. Format will look like...

ST 70-24237 BF 0123 BDY
TR 258 B80 10 10 PNT
08C 012345 678910

Again, private message me.

Held for Ransom 09-07-2006 09:15 PM

2 Attachment(s)
Update, forgot to add the other added wiring harness ground wire pictures.

gloryrestoparts 09-03-2010 09:21 PM

Quote:

Originally Posted by Held for Ransom (Post 2638793)
Update, forgot to add the other added wiring harness ground wire pictures.

PERFECT!!!! thats the ground I'm missing.


All times are GMT -4. The time now is 04:29 AM.