Burlwood applique
 

I have a 68 AT console and I was wondering if anyone has purchased the aftermarket burlwood decals and installed them on their console? WAs wondering if the aftermarket decals look like the original and if in general you were happy with the install and overall appearance? Thx.

Ive been after that for years
found enough of it to do a couple but it was sure pricey,(not for sale).
the reproduction stuff is cheesy.

Are they making the Burlwood replacement panels? When I was looking could only get the woodgrain which was wrong for my car.

NPD and a couple places (through eBay) are sellling the pre-cut Burlwood decals that you can glue to your console or dash center piece....I believe its a vinyl type decal. I have some I bought from NPD about 5 years ago and it wasnt an exact duplicate of the original but close. I wondered if NPD has updated it in the past 5 years or if the eBay guys (some place in Oregon, route66 or something on eBay) have updated to better matching decals.

I was in the parking lot of a local store this week and looked at the interior of a newer Lexus and saw that they had the Burlwood design on some of their dash and console pieces that looked almost exactly like that on the 68......I wonder how they are doing theirs?

I looked thru my Classic Ind. catalog recently and saw where the console and the console compartment door are being reproduced and sold now with the "correct burlwood grain" coating (the PRNDL shifter faceplate too). Anybody know how to figure out who is making these parts and what they are using for the Burlwood coating? The burlwood (decal/vinyl/whatever) must be being produced/available somewhere?

Probably with real wood.

I think your right....I skimmed a couple of articles that said recently (past 10 years or so)Cadillac and Lincoln are using real wood on some of their models now too. Looks good on the Lexus thats for sure.

I'm trying to look into using real Walnut Burl Wood veneer on my 68 console parts.....I might buy a small piece of the real veneer and see if I can make it work and look good. Might be too much work though.....

I purchased the decals I believe from PY years ago. I was happy with them although they are somewhat lighter in color. The fit was good but you I had to use the 3M heavy adhesive on some of the ends that wrap around and under to make them stay put. I also developed a 1" bubble due to direct heat from sunlight on one of the door ends. I am going to inject some adhesive into it with a hypo needle, and lay a flat weight on it for a week.

Steve....I if you get a chance, I would be interested in seeing some pics (if you have them and its not to much trouble to post) of your console in your car to see how it looks with the vinyl Burlwood you installed. I have those same vinyl Burl decals and my only hesitation to installing them was because, as you said, they are a bit lighter than the original......but if they look good... that would be the easiest route for me to go.

I have a picture of it installed on the dash in my 69. I bought it from PY a month ago and really like it.

Trent
http://forums.maxperformanceinc.com/...&d=1267119415,

Burl wood graining 1969 Firebird
 

I have the same problem, but I was going to buy the new console complete from Classic Ind. However, they will offer only the 1969 as an automatic. I need a 4 speed. I asked if they could just provide it with out a cut out, they said no. Also, I have been waiting over 1 year since they put it in the catalog, and it is still not available. If there is a material to re-cover mine that is correct but just a little light, I would sure like to know where to buy it so I could just move on until something better is available.

Thanks - Jim

I think that reproduction console has been a "Coming soon!" item for about 4 years now. I feel sorry for anyone that pre-paid. Ames Perf and others also listed it in their catalogs, but no one has received one.

Ah Ha....well I guess there is nothing new on the Burlwood applique stuff for the console then.....so back to working with whats available.

That looks nice on your dash Trent!

Page 32 of national parts depot online Firebird catalog has the burlwood applique type decals there. I bought mine from them a few years ago.....the ones I have are a bit lighter and has less texture than the original and the decal/vinyl is actually kinda thick so It might take some work and fanagaling to apply like Steve K has indicated in this thread.

I picked up a small piece of this stuff on epay......When I get it Im gonna see how it looks in the car.....it could look decent or end up looking real "cheesy" so I'm not sure. I kinda liked it in the picture on epay....but you never know what your gonna get on there so....


http://cgi.ebay.com/ebaymotors/ws/eB...K%3AMEWAX%3AIT

I think thats the same stuff thats been available for years.
Pattern is different as are the colors. I also havent found any that
has the texture of the OEM except for a partial roll I bought years ago.
I matched it up with a glove box lid on a 68 Bonny(same stuff) and its as perfect as a fingerprint.

Thanks! I refuse to show the turned engine vinyl I had on it before. lol,
Ok, I experimented. I failed.

After a long difficult search.....I finally found some Burlwood "applique" that I like. Real walnut burlwood.

Where did you find it and how much did it cost?