Forum: Electrical Tech
02-08-2006, 08:31 AM
|
Replies: 4
Views: 281
67 GTO Gas Gage
My gas gas does not always reflect the true quanity of the tank.I have replaced everything , except the Gage in the dash. I also spoke with the owner before me and he had the same issues. QUESTION ??...
|
Forum: Electrical Tech
07-22-2005, 09:00 AM
|
Replies: 9
Views: 684
|
Forum: Pontiac - Race
07-16-2005, 07:34 AM
|
Replies: 92
Views: 929
Looks just like mine did on 6-14-05 .# 3 broke...
Looks just like mine did on 6-14-05 .# 3 broke and it was down hill and a mess after that.Cam busted in 6 plcs. 4 rods broke and the oil pan looked like a target shoot with a 50 cal.Race prepped cast...
|
Forum: Pontiac - Race
06-18-2005, 05:08 PM
|
Replies: 24
Views: 379
After what I saw today from a cam braking in 6...
After what I saw today from a cam braking in 6 pcs. then digested a section through the rods and crank. As I tore it down I cheaked the torques and inspected the bearings Not one main bearing showed...
|
Forum: Pontiac - Race
06-18-2005, 04:41 PM
|
Replies: 7
Views: 98
Well I tore it down and out last night and this...
Well I tore it down and out last night and this am.The CAM Broke in 6 pcs. It broke at the fwd. side of # 2,3,& 4 bearings.The area between three & four was in two pcs, with the aft piece for #5 cyl....
|
Forum: Pontiac - Race
06-18-2005, 04:41 PM
|
Replies: 7
Views: 98
Well I tore it down and out last night and this...
Well I tore it down and out last night and this am.The CAM Broke in 6 pcs. It broke at the fwd. side of # 2,3,& 4 bearings.The area between three & four was in two pcs, with the aft piece for #5 cyl....
|
Forum: Pontiac - Race
06-16-2005, 04:14 PM
|
Replies: 24
Views: 504
I really hope I don't see that.But I will be...
I really hope I don't see that.But I will be looking under the bearings for signs.Starting tomorrow night I will be pulling it. So, saturday morning it should be on the stand with Tears dripping...
|
Forum: Pontiac - Race
06-16-2005, 04:07 PM
|
Replies: 24
Views: 504
|
Forum: Pontiac - Race
06-16-2005, 04:03 PM
|
Replies: 148
Views: 1,944
|
Forum: Pontiac - Race
06-16-2005, 03:57 PM
|
Replies: 24
Views: 504
|
Forum: Pontiac - Race
06-16-2005, 03:48 PM
|
Replies: 24
Views: 504
|
Forum: Pontiac - Race
06-16-2005, 03:14 PM
|
Replies: 24
Views: 504
|
Forum: Pontiac - Race
06-16-2005, 12:15 PM
|
Replies: 148
Views: 1,944
|
Forum: Pontiac - Race
06-16-2005, 12:07 PM
|
Replies: 24
Views: 504
Half Inch Request. 30 Weight Synthetic, .0025...
Half Inch Request. 30 Weight Synthetic, .0025 clearances,Race/ Polished, prepped Pontiac Rods. I haven't pulled it yet but, the rods I can see through the pan are broken just below the lower edge of...
|
Forum: Pontiac - Race
06-14-2005, 05:58 PM
|
Replies: 24
Views: 504
|
Forum: Pontiac - Race
06-14-2005, 05:58 PM
|
Replies: 24
Views: 504
|
Forum: The Body Shop TECH
03-09-2005, 04:38 PM
|
Replies: 143
Views: 7,247
|
Forum: Pontiac - Race
02-16-2005, 08:24 AM
|
Replies: 17
Views: 207
|
Forum: Pontiac - Race
02-15-2005, 01:13 PM
|
Replies: 17
Views: 207
Actually Rob, I Had a rear seal leaking so, I...
Actually Rob, I Had a rear seal leaking so, I pulled the Engine @ about 1200 miles. I pulled the Main caps, No issues. I also inspected the Rod bearings, No issues. Main concern was looking for...
|
Forum: Pontiac - Race
02-15-2005, 09:41 AM
|
Replies: 17
Views: 207
I bluprinted a 455 @ .060 overbore. Both deck...
I bluprinted a 455 @ .060 overbore. Both deck Heights were measured & they were off and had some difference end to end. My machinist zeroed both sides to zero from crank centerline , then we took the...
|
Forum: Pontiac - Race
02-01-2005, 09:44 AM
|
Replies: 9
Views: 71
I mounted my double Filter manifold to the Core...
I mounted my double Filter manifold to the Core support Pass. Side. Then had new hoses made with correct ends to allow routing them neatly down the frame rail as far from headers as possible. This...
|
Forum: 66-67 GTO Tempest & LeMans TECH
01-31-2005, 09:55 AM
|
Replies: 12
Views: 135
|
Forum: 66-67 GTO Tempest & LeMans TECH
01-31-2005, 09:45 AM
|
Replies: 5
Views: 91
|
Forum: Electrical Tech
01-12-2005, 08:29 AM
|
Replies: 4
Views: 170
67 GTO. I will look today at the rear of the...
67 GTO. I will look today at the rear of the gage. I did think about bending the float simply because it was off the same amount Full or empty.The only thing I remember about my gage was that it had...
|
Forum: Electrical Tech
01-12-2005, 07:27 AM
|
Replies: 3
Views: 136
What I did on my 67 GTO was to remove the Dash...
What I did on my 67 GTO was to remove the Dash Light harness assy. from main harness and built a new one. Very easy, and in doing so I used 194 bulbs and Side marker sockets from Help Parts rack @...
|