Forum: 61-77 GTO LeMans & Tempests FOR SALE
04-01-2011, 09:28 PM
|
Replies: 1
Views: 857
|
Forum: 61-77 GTO LeMans & Tempests FOR SALE
11-02-2010, 03:31 PM
|
Replies: 26
Views: 3,024
|
Forum: Electrical Tech
04-25-2010, 11:44 AM
|
Replies: 1
Views: 73
Blinker light sequence
I just finished checking my turn signal lights, brake lights, and tail lights, on a 1970 lemans sport that i am restoring. All the lights work correctly i think, there are 3 sockets with a side...
|
Forum: The Body Shop TECH
04-20-2010, 06:32 PM
|
Replies: 1
Views: 152
NOS front valance / brackets
I am working on a 1970 gto clone. I need some advice or pics of the front valance panel support brackets, where they bolt up at . I am having problems with the bolt holes lining up with the valance....
|
Forum: Suspension TECH
04-05-2010, 11:11 AM
|
Replies: 11
Views: 334
I just replaced the whole brake system on my 70...
I just replaced the whole brake system on my 70 lemans, had a hard time bleeding down the brake lines. I rented a vacuum pump from a auto store, connected the pump to the front and back brake lines,...
|
Forum: Suspension TECH
03-05-2010, 09:45 PM
|
Replies: 7
Views: 326
re
The pinion came out after using a bigger hammer and a bigger block of wood, bigger is better I guess. I ordered and recieved me pinion bearing overhaul set, one thing it didn't have was the axle...
|
Forum: Suspension TECH
03-01-2010, 01:56 AM
|
Replies: 7
Views: 326
|
Forum: Suspension TECH
02-28-2010, 07:06 PM
|
Replies: 7
Views: 326
Pinion Removal
I am replacing the bearings, seals and races on a 10 bolt single trac rear end. It is a 10 bolt rear end on a 1970 lemans sport and has 27 teeth on the spline. I have marked everything and removed...
|
Forum: Suspension TECH
02-28-2010, 01:42 PM
|
Replies: 14
Views: 595
I agree with powder coating, the best paint...
I agree with powder coating, the best paint application possible, wish I had done mine that way. In his situation he can only go back and sandblast again, and go with powder coat, or sand back down...
|
Forum: Suspension TECH
02-28-2010, 12:18 PM
|
Replies: 14
Views: 595
I had my wheels sandblasted, but I primed them...
I had my wheels sandblasted, but I primed them with 2 coats of epoxy primer, sanding them in between coats. You have to sand down every coat of paint, if your going to apply another coat over them,...
|
Forum: Suspension TECH
02-27-2010, 12:37 PM
|
Replies: 4
Views: 295
I pulled the cover off, and it is a standard...
I pulled the cover off, and it is a standard differential, the gear oil inside looked like tar. I ordered a bearing and seal kit through JEG, and should get it back by March 3rd. I have removed...
|
Forum: Suspension TECH
02-24-2010, 05:10 PM
|
Replies: 4
Views: 295
Standard Differential
I have a WC code on my differential, is this a limited slip differential or a regular differential where only one wheeel turns in drive and one wheel turns in reverse, is this a plain jane...
|
Forum: Suspension TECH
02-20-2010, 07:46 PM
|
Replies: 7
Views: 288
Front end pics
OK, here it is with the weight of then engine on the frame. As of right now the lower control arm has not been torqued down. I stood on the frame with the engine sitting on the mounts and jumped up...
|
Forum: Suspension TECH
02-20-2010, 07:38 PM
|
Replies: 5
Views: 295
re
I just completed the same job on my 70 Lemans Sport, as far as the torque goes I don't know , but the only control arm I didn't torque was the lower control arm. The manual states to torque the lower...
|
Forum: Suspension TECH
02-20-2010, 03:06 PM
|
Replies: 7
Views: 288
No all of the shims have been removed, I will...
No all of the shims have been removed, I will post a pic later today and you will have a better idea, will include a bird's eye view of the top control arm just to make sure it's on there right.
|
Forum: Suspension TECH
02-20-2010, 03:04 PM
|
Replies: 7
Views: 288
|
Forum: Suspension TECH
02-19-2010, 10:31 PM
|
Replies: 7
Views: 288
too much negative camber
First off this suspesion stuff is kinda new to me. I took alot of advice from this forum before I decided to do anything to my 70 lemans sport. I replaced everything all upper and lower bushings,...
|
Forum: Suspension TECH
02-03-2010, 05:10 PM
|
Replies: 2
Views: 247
Front brake lines
I recently did the front drum brake to disc brake conversion. Will I have to change out the frone brake lines, also will I have to change out the front brake reservior.
|
Forum: Suspension TECH
02-02-2010, 09:25 PM
|
Replies: 13
Views: 779
Front frame
196010
Finished up the front end, except the front stabilizer bar. I need to torque the lower control arm bushing bolts on each side, the service manual says torque at curb height. To me that...
|
Forum: Electrical Tech
01-27-2010, 04:10 PM
|
Replies: 18
Views: 528
|
Forum: Electrical Tech
01-27-2010, 03:45 PM
|
Replies: 18
Views: 528
|
Forum: Electrical Tech
01-26-2010, 08:15 PM
|
Replies: 43
Views: 2,027
|
Forum: Suspension TECH
01-26-2010, 05:08 PM
|
Replies: 13
Views: 779
Front coil springs
I am changing out the front coil springs on a 70 lemans sport. I ordered a set of moog 5440 springs through moog. I was told that was the one I needed, when I opened the box I looked at both ends and...
|
Forum: Electrical Tech
01-26-2010, 04:46 PM
|
Replies: 18
Views: 528
|
Forum: Electrical Tech
01-26-2010, 03:46 PM
|
Replies: 18
Views: 528
Looks like I was wrong , I am hooked into the...
Looks like I was wrong , I am hooked into the resistor wire, I went back and hooked up a battery wire to the hei and it works, it was trying to start but as soon as i let the key go it died, I need...
|