Forum: Tri-Power Tech
01-16-2025, 06:29 PM
|
Replies: 14
Views: 523
In 1964, I bought a GTO with a single AFB.four...
In 1964, I bought a GTO with a single AFB.four barrel. I added Doug's three tube headers, modified the distributor advance curve, added Hoosier slicks. Before these mods, the car ran 14,08@100.00...
|
Forum: Tri-Power Tech
07-23-2024, 01:09 PM
|
Replies: 4
Views: 858
Tri-Power setups obviously have three...
Tri-Power setups obviously have three needle/seats. Quadrajets have one. Holley's have two.
At full throttle, isn't it logical that the three fuel inlets allow more flow than any single carb? I...
|
Forum: 64-65 GTO Tempest & LeMans TECH
05-23-2024, 12:37 PM
|
Replies: 7
Views: 1,145
|
Forum: 64-65 GTO Tempest & LeMans TECH
03-22-2024, 04:49 PM
|
Replies: 97
Views: 69,581
|
Forum: THE LOBBY
02-14-2024, 01:41 PM
|
Replies: 70
Views: 7,395
Very disappointing. I believe most of us would...
Very disappointing. I believe most of us would much prefer an increase in dues rather than a digital magazine. This may be the beginning of the end of POCI. I'm 81 years old and have been a member...
|
Forum: 61-66 Big Pontiac TECH
01-19-2024, 05:29 PM
|
Replies: 2
Views: 1,039
Carter AFB
Whenever I restore an AFB, the screws, levers, and rods are bare steel. Can someone post a picture or describe to me what color they were plated when new?
I would like to do them correctly, rather...
|
Forum: Tri-Power Tech
12-22-2023, 05:18 PM
|
Replies: 5
Views: 1,947
|
Forum: Pontiac - Street
11-11-2023, 02:29 PM
|
Replies: 46
Views: 7,094
Yes, in the '60's, when most of our Pontiac...
Yes, in the '60's, when most of our Pontiac engines were produced, lifters were about $1.00 each. Cams were $25. We installed them and had very few failures, even with high valve spring pressures.
...
|
Forum: Tri-Power Tech
11-06-2023, 11:44 AM
|
Replies: 15
Views: 3,806
|
Forum: Tri-Power Tech
10-20-2023, 08:01 PM
|
Replies: 8
Views: 1,873
|
Forum: Pontiac - Street
10-08-2023, 12:57 PM
|
Replies: 8
Views: 1,256
|
Forum: Tri-Power Tech
07-27-2023, 12:24 AM
|
Replies: 17
Views: 2,874
|
Forum: 64-65 GTO Tempest & LeMans TECH
04-15-2023, 01:13 PM
|
Replies: 12
Views: 1,926
My father-in-law was an engineer at AO Smith in...
My father-in-law was an engineer at AO Smith in Milwaukee, where most GM frames were built until the 1970's. He said that the movement or twist on a typical automobile from one corner to the opposite...
|
Forum: Pontiac - Street
02-17-2023, 08:56 PM
|
Replies: 71
Views: 12,282
|
Forum: Tri-Power Tech
02-05-2023, 02:09 AM
|
Replies: 13
Views: 2,199
|
Forum: Pontiac - Street
01-20-2023, 06:24 PM
|
Replies: 42
Views: 7,657
|
Forum: Pontiac - Street
01-03-2023, 12:49 AM
|
Replies: 40
Views: 5,858
I agree with Tom V. I have not used liquid carb...
I agree with Tom V. I have not used liquid carb cleaner for many years. I have a blast cabinet and I use glass beads on carb bodies. This results in a shiny finish ready for dichromate finish just as...
|
Forum: THE LOBBY
12-23-2022, 05:55 PM
|
Replies: 72
Views: 9,646
|
Forum: Tri-Power Tech
12-16-2022, 05:16 PM
|
Replies: 51
Views: 23,495
|
Forum: Pontiac - Street
12-05-2022, 01:44 AM
|
Replies: 55
Views: 8,819
|
Forum: Pontiac - Street
12-03-2022, 12:53 AM
|
Replies: 55
Views: 8,819
|
Forum: Pontiac - Street
11-02-2022, 11:19 AM
|
Replies: 66
Views: 13,965
|
Forum: National Events
08-16-2022, 12:51 AM
|
Replies: 55
Views: 20,263
|
Forum: 64-65 GTO Tempest & LeMans TECH
04-27-2022, 10:07 AM
|
Replies: 15
Views: 2,898
|
Forum: Tri-Power Tech
02-19-2022, 11:15 AM
|
Replies: 32
Views: 11,795
|