Showing results 1 to 25 of 108
Search took 0.01 seconds.
Search: Posts Made By: Nobuddy
Forum: Pontiac - Street 02-26-2024, 01:28 AM
Replies: 21
Views: 1,316
Posted By Nobuddy
Crower "Cam Saver" is only for flat hydraulics. ...

Crower "Cam Saver" is only for flat hydraulics. It is a flat ground in the side of the lifter from the oil band to the face as a controlled leak for extra oil to the cam lobe/lifter face. So if you...
Forum: Pontiac - Race 01-04-2024, 01:47 AM
Replies: 40
Views: 2,612
Posted By Nobuddy
Six days, four tracks. Starts in Orlando, then...

Six days, four tracks. Starts in Orlando, then Bradenton FL, Gainesville FL, Adel GA, and back to Orlando. You turn in a best time slip each day and cumulative times determine winners for each...
Forum: THE LOBBY 12-19-2023, 11:53 PM
Replies: 88
Views: 8,215
Posted By Nobuddy
Has been a long time, but I believe you remove...

Has been a long time, but I believe you remove the cover on the top right side of the winch to access where the push/pull cables attach and are adjusted. I'm sure there is a manual for a D7D winch...
Forum: Pontiac - Race 12-04-2023, 11:22 AM
Replies: 135
Views: 15,947
Posted By Nobuddy
Similar on mine and depends on the studs and...

Similar on mine and depends on the studs and guideplates used. With the original tangs removed, ARP 100-7101 bottomed out. The blind hole is deep enough so I just wound out their coil, used a...
Forum: Pontiac - Street 11-30-2023, 12:01 PM
Replies: 816
Views: 60,354
Posted By Nobuddy
BonAmi cleanser, not Comet.:).

BonAmi cleanser, not Comet.:).
Forum: Pontiac - Street 11-28-2023, 03:07 PM
Replies: 816
Views: 60,354
Posted By Nobuddy
Personally, I think you guys are getting trolled....

Personally, I think you guys are getting trolled. LOL
Forum: Pontiac - Street 10-30-2023, 03:38 AM
Replies: 13
Views: 770
Posted By Nobuddy
#12-24 which is a standard UNC thread.

#12-24 which is a standard UNC thread.
Forum: Pontiac - Street 09-08-2023, 09:58 AM
Replies: 41
Views: 1,640
Posted By Nobuddy
I know opinions vary but I don't think calipers...

I know opinions vary but I don't think calipers are reliable to check finer than .001. Use a decent .0001 micrometer. Or just plastigage to backup your bore gage/caliper indication. If a caliper...
Forum: Pontiac - Street 08-23-2023, 01:34 AM
Replies: 398
Views: 68,524
Posted By Nobuddy
Perhaps you could cut the Chevy bones and weld...

Perhaps you could cut the Chevy bones and weld with correct spacing? Seems much easier and avoids a lot of unknowns.

Barry
Forum: Pontiac - Street 08-16-2023, 10:27 AM
Replies: 32
Views: 1,409
Posted By Nobuddy
Are there are any aftermarket valley pans that...

Are there are any aftermarket valley pans that will clear the EGR manifold? Assuming the OEM pan cannot be made to clear link bar lifters.

Thread is interesting to me as I still have the...
Forum: Members Helping Members 08-11-2023, 11:16 AM
Replies: 9
Views: 388
Posted By Nobuddy
I have one that I bought to also repair a mower. ...

I have one that I bought to also repair a mower. Worked well on the original aluminum threads but they were only buggered for maybe the top thread. Sure beat pulling the head off and using a...
Forum: THE LOBBY 07-14-2023, 01:36 AM
Replies: 102
Views: 5,110
Posted By Nobuddy
Probably Tacoma's with frames from Dana corp. ...

Probably Tacoma's with frames from Dana corp. Made in America for what it's worth.
Forum: Members Helping Members 06-23-2023, 01:55 PM
Replies: 5
Views: 538
Posted By Nobuddy
Some kind of underlayment is required or you risk...

Some kind of underlayment is required or you risk rot in the T-111 from condensation. But probably not an actual vapor barrier like polyethylene sheet. Tyvek isn't a vapor barrier, it blocks air...
Forum: THE LOBBY 06-19-2023, 11:04 AM
Replies: 68
Views: 3,855
Posted By Nobuddy
For what its worth, "homologation" does not mean...

For what its worth, "homologation" does not mean that a car was made from existing parts from other cars. It just means that a specific configuration has been defined by a manufacturer and approved...
Forum: Pontiac - Street 06-18-2023, 11:37 PM
Replies: 12
Views: 726
Posted By Nobuddy
Not the prettiest solution but the inductive Tiny...

Not the prettiest solution but the inductive Tiny Tach will work.

https://tinytach.com/tinytach
Forum: Pontiac - Street 06-12-2023, 06:18 PM
Replies: 38
Views: 2,471
Posted By Nobuddy
I wasn't really thinking about budget, it was...

I wasn't really thinking about budget, it was just keeping known good original parts. Assuming of course that they pass inspection.
Forum: Pontiac - Street 06-12-2023, 01:19 PM
Replies: 38
Views: 2,471
Posted By Nobuddy
OJ - I'm sure many will disagree with me, but...

OJ - I'm sure many will disagree with me, but from what you have described I would be tempted to just clean and reassemble the engine then see how it runs. Assuming your inspections find nothing...
Forum: Pontiac - Street 04-24-2023, 11:11 AM
Replies: 20
Views: 1,173
Posted By Nobuddy
Your theory is wrong. Bolts are not a substitute...

Your theory is wrong. Bolts are not a substitute for rivets.
Forum: Pontiac - Street 04-06-2023, 10:28 AM
Replies: 57
Views: 3,163
Posted By Nobuddy
Detroit Diesel peanut butter

Great stuff but don't use "peanut butter" for fastener lube unless you really know what you are doing.
Forum: Pontiac - Race 03-31-2023, 01:49 AM
Replies: 27
Views: 3,178
Posted By Nobuddy
Thank you for the follow up.

Thank you for the follow up.
Forum: Pontiac - Race 03-30-2023, 01:48 PM
Replies: 27
Views: 3,178
Posted By Nobuddy
So when finishing bushings, you just go straight...

So when finishing bushings, you just go straight to the hone and no reamer?
Forum: Members Helping Members 03-26-2023, 08:43 PM
Replies: 9
Views: 970
Posted By Nobuddy
I just now saw you are in Australia. "Hobart...

I just now saw you are in Australia. "Hobart Brothers" is owned by Illinois Tool Works who also owns Miller Welding so probably found at same welding suppliers. They make welding machines, supplies...
Forum: Industry Stuff 03-26-2023, 04:34 PM
Replies: 25
Views: 6,246
Posted By Nobuddy
Plus there is CWC, the foundry that manufacturers...

Plus there is CWC, the foundry that manufacturers the cast cores used by CMC. CWC is owned by Textron who is owned by Kautex. Kautex is global and does a lot of OEM work so I expect old Pontiac or...
Forum: Pontiac - Street 03-26-2023, 02:01 PM
Replies: 20
Views: 2,073
Posted By Nobuddy
I have not heard of anyone offering a CNC recut...

I have not heard of anyone offering a CNC recut of the Speedmaster chambers but I expect it could be done. By hand for that matter. Leaving the valve seats alone and opening it up.

I believe...
Forum: Members Helping Members 03-26-2023, 10:53 AM
Replies: 9
Views: 970
Posted By Nobuddy
These rods are not all the same. I suggest you...

These rods are not all the same. I suggest you try the Hobart. Small packages on the shelf at Home Depot or Northern Tool.
Showing results 1 to 25 of 108

 
Forum Jump

All times are GMT -4. The time now is 03:59 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017