test
Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: 61-63
Forum: 61-66 Big Pontiac TECH 06-13-2021, 02:27 PM
Replies: 7
Views: 228
Posted By 61-63
Here are two pictures of the bracket. It is the...

Here are two pictures of the bracket. It is the same regardless of trans and bolts on with the rear two driver's side intake bolts as mgarblik said.. It is the bracket pfilean's pictured in his post.
Forum: Pontiac - Street 06-10-2021, 04:26 PM
Replies: 16
Views: 502
Posted By 61-63
This is a personal preference thing but an Offy...

This is a personal preference thing but an Offy dual quad setup can be made to look almost identical to the '61-'63 inline SD setups. The difference in the spacing on the carbs between the read SD...
Forum: Pontiac - Street 06-07-2021, 02:59 PM
Replies: 11
Views: 652
Posted By 61-63
Put the body on a mill table so you can get dead...

Put the body on a mill table so you can get dead nuts on center, then ine up on each jet with HSS BS3 center drill, then drill with 1/4" bit, follow with 17/64" bit, then retap with a 5/16 NF 24...
Forum: Pontiac - Street 06-03-2021, 07:52 AM
Replies: 5
Views: 371
Posted By 61-63
Slick! Good job.

Slick! Good job.
Forum: THE LOBBY 05-25-2021, 10:17 AM
Replies: 13
Views: 1,224
Posted By 61-63
HALFWAY I don't think you're affected unless your...

HALFWAY I don't think you're affected unless your wife passes and you begin to receive survivor benefits from her pension, if she chose to give them to you when she retired. At that point your ss...
Forum: 61-66 Big Pontiac TECH 05-24-2021, 06:55 PM
Replies: 8
Views: 377
Posted By 61-63
That picture of the remote passenger side mirror...

That picture of the remote passenger side mirror is the first time I've ever seen one.
Forum: THE LOBBY 05-24-2021, 06:49 PM
Replies: 13
Views: 1,224
Posted By 61-63
I'm pretty sure deductions similar to what you...

I'm pretty sure deductions similar to what you state above have been in effect since far earlier than 2004. Retired federal employees cannot receive both social security and federal retirement even...
Forum: Pontiac - Street 05-19-2021, 07:01 PM
Replies: 31
Views: 1,812
Posted By 61-63
I vote with the crowd telling you to store the...

I vote with the crowd telling you to store the original engine and build the 455 with the factory crank.
Forum: Tri-Power Tech 05-18-2021, 09:58 PM
Replies: 12
Views: 1,219
Posted By 61-63
I would say that was dropped from pretty high up;...

I would say that was dropped from pretty high up; like mebby off of a conveyer belt coming out of a 747 or something?
Forum: Pontiac - Street 05-17-2021, 07:46 PM
Replies: 18
Views: 1,013
Posted By 61-63
Great video ...

Great video

https://www.youtube.com/watch?v=9LuXf6gJ-jg
Forum: THE LOBBY 05-17-2021, 10:37 AM
Replies: 47
Views: 2,268
Posted By 61-63
Great place. Now you need small kubota, a two...

Great place. Now you need small kubota, a two post lift, welders, oxy/acetylene and plasma cutter, big air compressor, blasting cabinet, and a couple of big tool chests full of tools. You may have...
Forum: Pontiac - Street 05-13-2021, 05:36 PM
Replies: 61
Views: 2,445
Posted By 61-63
When you "very lightly" add speed there is a good...

When you "very lightly" add speed there is a good chance you aren't getting any squirt at all thus a nozzle change won't help you.

Get a pair of Pontiac AFB nozzles and drill them out to a larger...
Forum: 61-66 Big Pontiac TECH 05-12-2021, 10:17 AM
Replies: 13
Views: 947
Posted By 61-63
Looks like a nice, solid car. Good luck with it!

Looks like a nice, solid car. Good luck with it!
Forum: Pontiac - Street 05-11-2021, 12:20 PM
Replies: 61
Views: 2,445
Posted By 61-63
The step up pistons and springs in afb and...

The step up pistons and springs in afb and edelbrock knockoffs including the avs are part of the main circuits and not the idle circuits. Part of his low vacuum at idle issue may be his idle rpm. ...
Forum: SOLD Parts 05-10-2021, 10:50 AM
Replies: 4
Views: 823
Posted By 61-63
Very nice and a good deal for someone IMO.

Very nice and a good deal for someone IMO.
Forum: Pontiac - Street 05-10-2021, 09:44 AM
Replies: 61
Views: 2,445
Posted By 61-63
1. As post #13 states you probably need to open...

1. As post #13 states you probably need to open up the idle mixture screws. I say "probably" because I don't know the angle of the points on the edelbrock mixture screws. Go around all four mixture...
Forum: Big Pontiacs(including G-body) FOR SALE 05-07-2021, 08:08 PM
Replies: 9
Views: 1,331
Posted By 61-63
Very nice car.

Very nice car.
Forum: Pontiac - Street 05-05-2021, 01:48 PM
Replies: 12
Views: 669
Posted By 61-63
Sounds like a neat engine to me. You will get...

Sounds like a neat engine to me. You will get lots of input but my only comments would be to go with the eheads rather than the cast iron and mebby use a built turbo 350 trans rather than a 400...
Forum: Pontiac - Street 05-05-2021, 11:12 AM
Replies: 16
Views: 825
Posted By 61-63
I don't think offy ever made a Pontiac intake...

I don't think offy ever made a Pontiac intake that looked like the above Buick design that some of you seem to like more. I've been buying used offy dual quad Pontiac intakes for years and putting...
Forum: Big Pontiacs(including G-body) FOR SALE 05-04-2021, 06:29 AM
Replies: 5
Views: 562
Posted By 61-63
If you go to Gateway's website they want $51k for...

If you go to Gateway's website they want $51k for that car.
Forum: SOLD Parts 05-03-2021, 10:43 AM
Replies: 9
Views: 997
Posted By 61-63
Ah I didn't realize the '64 hood had been...

Ah I didn't realize the '64 hood had been repopped.
Forum: SOLD Parts 05-02-2021, 05:44 PM
Replies: 9
Views: 997
Posted By 61-63
Well I'm surprised. Guess people aren't cloning...

Well I'm surprised. Guess people aren't cloning '64 Tempest and LeMans into GTOs anymore.
Forum: Pontiac - Street 05-01-2021, 12:43 PM
Replies: 46
Views: 2,305
Posted By 61-63
The primary counter arguments to what you are...

The primary counter arguments to what you are saying is that you can buy several 400 pistons off the shelf where 389 pistons must be special ordered, the only screw in or pinned studs in 389 heads...
Forum: Pontiac - Street 04-30-2021, 06:47 AM
Replies: 46
Views: 2,305
Posted By 61-63
Get #16 heads they are big valve open chamber...

Get #16 heads they are big valve open chamber heads with factory screw in studs. There are others and people will surely chime in.
Forum: Big Pontiac(incl G-body)Parts WANTED 04-26-2021, 06:04 PM
Replies: 7
Views: 591
Posted By 61-63
I have a '63 quick ratio power steering box I...

I have a '63 quick ratio power steering box I bought new probably ten years ago and never installed in my car, with the pitman arm. I need to dig it out of my stash and also look up what I paid for...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -4. The time now is 11:28 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 

Cold Case Radiators

Cold Case Radiators is a Max Performance company that produces high end aluminum performance radiators at a price point that won't break the bank. Polished and stamped tanks. 2 rows of 1" tubes. Lifetime Warranty.

GTOG8TA.com

GTOG8TA.com is a Max Performance company that manufacturers parts for the 04-06 GTO, 08-09 G8, and 93-02 Firebird/Trans Am platforms.

Copyright © 2017