Showing results 1 to 25 of 46
Search took 0.01 seconds.
Search: Posts Made By: dans1967
Forum: 66-67 GTO Tempest & LeMans TECH 07-21-2023, 01:21 PM
Replies: 5
Views: 511
Posted By dans1967
So, I bought two tools to remove the window trim....

So, I bought two tools to remove the window trim. One worked great for the front windshield, but I could not do the rear trim. I was given a contact at a glass repair shop who has worked on old cars....
Forum: 66-67 GTO Tempest & LeMans TECH 07-09-2023, 01:16 PM
Replies: 5
Views: 511
Posted By dans1967
Rear window molding removal

I am replacing my existing vinyl roof. I need to know how to remove the trim around the rear window from the clips that hold it in place. Which tool do I use and from which side of trim( vinyl or...
Forum: Exhaust TECH 05-11-2022, 03:58 PM
Replies: 5
Views: 1,406
Posted By dans1967
Went with the Dynomax 17732. These sound great,...

Went with the Dynomax 17732. These sound great, very satisfied.
Thanks for the help
Forum: Exhaust TECH 04-16-2022, 10:52 AM
Replies: 5
Views: 1,406
Posted By dans1967
muffler advice

67 gto with ram air manifolds, 2.25 exhaust pipes, no crossover, need new mufflers (blew one up) I want good sound but do not want a loud drone in the cabin. What is out there that would accomplish...
Forum: 66-67 GTO Tempest & LeMans TECH 07-17-2020, 02:17 PM
Replies: 2
Views: 1,103
Posted By dans1967
I think I solved my problem. It appears an inside...

I think I solved my problem. It appears an inside contact slid up and touched the upper frame, causing short. Probably happened when I put the new harness on the panel. I believe the contacts and...
Forum: 66-67 GTO Tempest & LeMans TECH 07-16-2020, 02:07 PM
Replies: 2
Views: 1,103
Posted By dans1967
Rebuild ac , heater control panel

Need help with a control switch, it is now causing a short and blowing fuse. What is the proper sequence of these contacts and spacers? Pencil points to master switch.

Thanks in advance
Forum: 66-67 GTO Tempest & LeMans TECH 09-25-2019, 10:40 PM
Replies: 12
Views: 2,579
Posted By dans1967
Update; Put in a summit mini starter, wrapped...

Update; Put in a summit mini starter, wrapped with heat shield, replaced the timing chain and sprockets, found a loose ground wire, removed the rev limiter chip from the MSD unit, set the timing at...
Forum: SOLD Parts 08-29-2019, 08:34 PM
Replies: 10
Views: 1,632
Posted By dans1967
Hi Bob I am interested in your manifolds. I...

Hi Bob I am interested in your manifolds. I presently have a 67 with a 400 that has headers which I want to remove and go back to stock. Car also has 670 heads. Can you please tell me the part...
Forum: 66-67 GTO Tempest & LeMans TECH 08-10-2019, 02:14 PM
Replies: 12
Views: 2,579
Posted By dans1967
Which powermaster are you using

Which powermaster are you using
Forum: 66-67 GTO Tempest & LeMans TECH 08-10-2019, 01:37 PM
Replies: 12
Views: 2,579
Posted By dans1967
I had to put new weights and springs because of...

I had to put new weights and springs because of light rust buildup.
Forum: 66-67 GTO Tempest & LeMans TECH 08-10-2019, 10:16 AM
Replies: 12
Views: 2,579
Posted By dans1967
Finally got back to the car. My initial timing is...

Finally got back to the car. My initial timing is 7, just checked. Ran engine, warmed to normal temp then tried to restart. Starter motor turned over slowly. Labored very hard.. battery is new and...
Forum: 66-67 GTO Tempest & LeMans TECH 07-26-2019, 01:54 PM
Replies: 12
Views: 2,579
Posted By dans1967
timing question. can it change when the car is hot causing restart problem

After short drive car will not start (400 engine, tripower setup)normal temp 175.
Car seemed to burp thru center carb while trying to start. New battery, plenty of crank. MSD ignition rebuilt...
Forum: Pontiac - Street 05-05-2019, 05:46 PM
Replies: 2
Views: 402
Posted By dans1967
thanks, took a few trials, and then fell into...

thanks, took a few trials, and then fell into place.
Thanks again.
Forum: Pontiac - Street 05-05-2019, 01:49 PM
Replies: 2
Views: 402
Posted By dans1967
distributor will not line up

I pulled the msd distributor to replace the advance weights and springs ( some rust). tried to drop it back into original position and cannot align properly. What moved when I took it out and can I...
Forum: 66-67 GTO Tempest & LeMans TECH 05-16-2016, 04:03 PM
Replies: 10
Views: 380
Posted By dans1967
the first line at the top has the letters SO ...

the first line at the top has the letters SO
the second line at the top has the word BROADC, broadcast I assume

car was built in Freemont, CA
Forum: 66-67 GTO Tempest & LeMans TECH 05-15-2016, 10:52 AM
Replies: 10
Views: 380
Posted By dans1967
Attached is a scan of the paper

Attached is a scan of the paper
Forum: 66-67 GTO Tempest & LeMans TECH 05-13-2016, 06:03 PM
Replies: 10
Views: 380
Posted By dans1967
Thank you, and yes I will scan. Paper is delicate...

Thank you, and yes I will scan. Paper is delicate and writing is light, but I will try it
Forum: 66-67 GTO Tempest & LeMans TECH 05-12-2016, 08:44 PM
Replies: 10
Views: 380
Posted By dans1967
67 broadcast sheet from under rear seat

I have a broadcast sheet that matches my serial number for the car. It is a series of blocks with numbers and letters.

seq no. model trim i understand this set.
430 24217 223

78 79 ...
Forum: 66-67 GTO Tempest & LeMans TECH 11-07-2015, 06:32 PM
Replies: 10
Views: 630
Posted By dans1967
Thanks for everyone"s advice

Thanks for everyone"s advice
Forum: 66-67 GTO Tempest & LeMans TECH 11-07-2015, 06:24 PM
Replies: 10
Views: 630
Posted By dans1967
Finally put some serious time into finding the...

Finally put some serious time into finding the problem. Spent several hours following wires, removing the fuse block, checking the bulbs and sockets- to no avail. Dawn finally broke over marblehead,...
Forum: 66-67 GTO Tempest & LeMans TECH 07-20-2015, 07:43 PM
Replies: 10
Views: 630
Posted By dans1967
I have my work cut out for me this weekend. Great...

I have my work cut out for me this weekend. Great info, will let you know what i find.
Forum: 66-67 GTO Tempest & LeMans TECH 07-18-2015, 08:37 AM
Replies: 10
Views: 630
Posted By dans1967
electrical problem-brake light fuse blows out

Own a 67 GTO. When I step on the brake the courtesy light above console lights up, eventually the brake light fuse blows. What is the best way to tackle this problem. Ground issue has been suggested,...
Forum: 66-67 GTO Tempest & LeMans TECH 09-01-2012, 04:00 PM
Replies: 5
Views: 155
Posted By dans1967
went to a local car show last evening and it...

went to a local car show last evening and it ended at dusk. I turned on my headlights to leave and still had no dash lights. At the first stop light i was looking at the full moon, then saw that my...
Forum: 66-67 GTO Tempest & LeMans TECH 08-30-2012, 07:14 PM
Replies: 5
Views: 155
Posted By dans1967
the fuse is good and it is new.

the fuse is good and it is new.
Forum: 66-67 GTO Tempest & LeMans TECH 08-29-2012, 05:40 PM
Replies: 5
Views: 155
Posted By dans1967
no dash lights

Just put in a new headlight switch, thought the new rehostat would solve problem. If I run a wire from the fuse block to a socket it will light up the bulb. how do I solve this problem.
67 GTO
Showing results 1 to 25 of 46

 
Forum Jump

All times are GMT -4. The time now is 05:36 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017