Forum: Pontiac - Street
01-20-2009, 07:48 PM
|
Replies: 28
Views: 1,435
A couple of points - I reused the original...
A couple of points - I reused the original Pontiac low mileage stamped steel rockers when I replaced the original cam with a HR. When installing a bigger cam 4 years and 20k miles later, I saw...
|
Forum: Pontiac - Street
01-18-2009, 11:06 PM
|
Replies: 4
Views: 259
|
Forum: Pontiac - Street
01-18-2009, 03:56 PM
|
Replies: 11
Views: 493
|
Forum: Members Helping Members
01-04-2009, 03:46 PM
|
Replies: 1
Views: 93
Fan noise in truck
I got this truck last Fall, 2000 GMC Sierra, 5.3, K1500, 100k miles. Do they have a problem with noisy fans? The fan was whining like the clutch was engaged when it shouldn't have been, for example...
|
Forum: Pontiac - Street
01-01-2009, 01:57 PM
|
Replies: 10
Views: 462
|
Forum: Pontiac - Street
12-31-2008, 04:42 PM
|
Replies: 14
Views: 596
|
Forum: Pontiac - Street
12-30-2008, 06:00 PM
|
Replies: 14
Views: 596
|
Forum: Pontiac - Street
12-30-2008, 04:22 PM
|
Replies: 28
Views: 1,363
|
Forum: Pontiac - Race
12-26-2008, 12:30 PM
|
Replies: 16
Views: 646
|
Forum: Pontiac - Street
12-26-2008, 12:07 PM
|
Replies: 7
Views: 716
|
Forum: Pontiac - Street
12-25-2008, 03:34 PM
|
Replies: 4
Views: 228
|
Forum: Pontiac - Street
12-15-2008, 10:47 PM
|
Replies: 7
Views: 503
I have had good success cleaning badly carboned...
I have had good success cleaning badly carboned valves with a wire wheel on a bench grinder. The steel of the valves is so hard, the wire wheel only removes carbon and doesn't harm the valve. I am...
|
Forum: Pontiac - Street
12-15-2008, 10:35 PM
|
Replies: 8
Views: 380
|
Forum: Pontiac - Street
12-13-2008, 09:46 PM
|
Replies: 74
Views: 2,522
|
Forum: Pontiac - Street
12-08-2008, 09:39 PM
|
Replies: 12
Views: 1,055
johnreeves, you definitely want flat tappet? A...
johnreeves, you definitely want flat tappet? A lot of people on here, including me, switched to hydraulic roller because of some break-in disasters with flat tappet cams. Expensive cam set but so is...
|
Forum: Pontiac - Street
12-08-2008, 09:26 PM
|
Replies: 15
Views: 1,014
|
Forum: Pontiac - Street
11-25-2008, 08:43 PM
|
Replies: 19
Views: 1,100
|
Forum: Pontiac - Street
11-25-2008, 08:16 PM
|
Replies: 2
Views: 412
Sounds great. Glad you found a good builder....
Sounds great. Glad you found a good builder. There's a lot of bad ones about.
Not sure about your exact car, but GM usually makes the low pressure return hose with gear clamps or similar on the...
|
Forum: Pontiac - Street
11-23-2008, 09:50 PM
|
Replies: 23
Views: 640
|
Forum: Pontiac - Street
11-23-2008, 09:17 PM
|
Replies: 23
Views: 640
|
Forum: Pontiac - Street
11-16-2008, 06:55 PM
|
Replies: 12
Views: 628
|
Forum: Pontiac - Street
11-06-2008, 11:29 PM
|
Replies: 10
Views: 601
|
Forum: Pontiac - Street
10-30-2008, 09:00 PM
|
Replies: 25
Views: 2,817
|
Forum: Pontiac - Street
10-28-2008, 09:01 PM
|
Replies: 6
Views: 341
|
Forum: Pontiac - Street
10-21-2008, 09:38 PM
|
Replies: 14
Views: 1,122
There are a few other possible causes. What is...
There are a few other possible causes. What is your compression ratio, rear axle ratio, initial ignition timing?
For some reason, there is very little info on PP springs. Even Cliff hardly touches...
|