| FAQ |
| Members List |
| Social Groups |
| Calendar |
| Search |
| Today's Posts |
|
|
|
#1
11-16-2001, 11:16 PM
|
||||
|
||||
I removed my aftermarket chrome valve covers from the 455 and the stock covers seem to be a bit short. Even though no oil drippers are installed on the factory covers, the roller rockers are hitting the lower edge of the covers slightly.
Two questions: Since this is an AC car, the air conditioning to intake braket is pretty close to the passenger side valve cover. Does anyone make a thicker gasket that will cure this problem? If not, any recommendations on tall covers that look a bit stock? If I use tall covers, I'll cut the AC bracket and modify it to fit. I'd rather use stock height valve covers, but the tick is driving me nuts. Dave |
|
#2
11-19-2001, 10:02 PM
|
||||
|
||||
|
Dave
Use Felpro part # 1627 - thick cork gaskets, had to use them to clear my roller rockers. Barry
__________________
66 Corvair Corsa - not so stock 74 Formula 400/4 sp - stock 79 TATA - almost stock 78 TA - owned it since new - not so stock (11.28 at 118.6) |
|
#3
11-20-2001, 12:08 AM
|
||||
|
||||
|
Same here. I ordered mine from Nunzi which were $26/pr. No more clearance problems. You may find you need a bit longer bolt for the valve covers.
|
|
#4
11-20-2001, 12:30 AM
|
||||
|
||||
|
Not sure how much clearence you need but, the Felpro #FPP-1627 is 1/4" thick as stated above and they are only @ $18.00 in Summit and Jegs!
__________________
|
|
#5
11-16-2001, 11:16 PM
|
||||
|
||||
|
I removed my aftermarket chrome valve covers from the 455 and the stock covers seem to be a bit short. Even though no oil drippers are installed on the factory covers, the roller rockers are hitting the lower edge of the covers slightly.
Two questions: Since this is an AC car, the air conditioning to intake braket is pretty close to the passenger side valve cover. Does anyone make a thicker gasket that will cure this problem? If not, any recommendations on tall covers that look a bit stock? If I use tall covers, I'll cut the AC bracket and modify it to fit. I'd rather use stock height valve covers, but the tick is driving me nuts. Dave |
|
#6
11-16-2001, 11:28 PM
|
||||
|
||||
|
Use 2 valvecover gaskets per valvecover.
or Spotty has the extra thick gaskets for this situation.
__________________
95 Towncar that needs more TQ. Sold 2023: 12.24/111.6MPH/1.76 60'/28"/3.54:1/SP-TH400/469 R96A/236-244-112LC/1050&TorkerI//3850Lbs//15MPG/89oct Sold 2003: 12.00/112MPH/1.61 60'/26"x3.31:1/10"/469 #48/245-255-110LSA/Q-Jet-Torker/3650Lbs//18MPG 94oct Sold 1994: 11.00/123MPH/1.50 60'/29.5"x4.10:1/10"/469 #48/245-255-110LSA/Dual600s-Wenzler/3250Lbs//94oct |
|
#7
11-16-2001, 11:30 PM
|
||||
|
||||
|
If I use two gaskets, should I use some RTV between the two or will they seal up without?
Dave |
| Reply |
|
|
The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.
Hybrid Mode
