[Cliff R]

Skip, the Crower rods simply keep me from getting that "pucker factor" when we spin the big 455 up near 6000rpm's, I sleep better at night too!

I've tried shifting at at every rpm between 4800 and 5800. There is less than a tenth to be had between those points, so I simply shift at 5000rpm's for bracket racing. It also give me some room to work during the run, if the car slips a tad on the launch or I don't think my RT was that good. I can "buzz" the engine a bit harder and make sure I get to the end first, not giving my opponent any room to back off the throttle.......Cliff

[Skip Fix]

Just giving you a hard time Cliff!

I agree with the good reasonable priced rods out there now why use cast. I had a definite pucker factor when we dynoed my first 455 with the RAIV heads and buzzed it to 6200 with cast rods! It wasn't shifted that high but did see 6000 s few times.The next motor that got those heads got Crower billets-before the less expensive rods were around.


Often these discussion get "I ran 11s and even 10s with all stock pieces" yet most of use do prefer a little added insurance in durability as we has taken parts designed for very low rpm, 300-370 hp motors and are twisting 500+ hp out of them, and then suprised when a component(block,crank,rod) fails, or that a totally redesigned head can make it easier to get those extra HP, but then make them "expensive" race motors.

I hauled my car to several races borrowing a friend's utility trailer. It pulled crappy and with a short wheelbase full sized Bronco and two scarey experiences I felt it wasn't worth dying for the cost of a dedicated car trailer.Good rods, rear end parts etc are the same way if they fail at track speed-why risk your life for a few hundred dollars.

[blaktopr]

Oh my god. How bout we pull out our blanks and see whos is the biggest. There we go, problem solved. Where in this thread does it mention what the title suggests. Port velocity vs volume. It should say "whos car goes this fast with this head port size, big or small" How about some talk on how some ports are the same size cc but has anyone checked with a mold on the shape? Probably different shapes. How about the relationship between these ports and the size of the motor or how the engine speed can effect the size and shape of a port or vice versa. Why do some guys run better............the size, the shape, the flow??? MMMMMMMMMMM. How bout a question, can a 250cc intake port have the same velocity as a 175cc intake port. How and why? Answers lead to more questions. But here a discussion can be had to get all those answers and cross reference them to different combos. Not why somebody dont run a number with a cirtain combo. Cmon people!!!!!!!!!!!!!

[blaktopr]

Oh my god. How bout we pull out our blanks and see whos is the biggest. There we go, problem solved. Where in this thread does it mention what the title suggests. Port velocity vs volume. It should say "whos car goes this fast with this head port size, big or small" How about some talk on how some ports are the same size cc but has anyone checked with a mold on the shape? Probably different shapes. How about the relationship between these ports and the size of the motor or how the engine speed can effect the size and shape of a port or vice versa. Why do some guys run better............the size, the shape, the flow??? MMMMMMMMMMM. How bout a question, can a 250cc intake port have the same velocity as a 175cc intake port. How and why? Answers lead to more questions. But here a discussion can be had to get all those answers and cross reference them to different combos. Not why somebody dont run a number with a cirtain combo. Cmon people!!!!!!!!!!!!!

[Steve C.]

It all goes back to Larry's initial post in this thread where on the first page of the article he posted it stated "flow quality is as important as flow quanity".

As already stated here, that statement is not new earth shaking news.
In the 2002 issue of Circle Track magazine Jim McFarland's tech article had this heading.... "Engine Airflow: More Than Just Numbers. Airflow quality can yield cost-effective performance gains."

Jim McFarland says, I recently asked a prominent engine builder, "What's the most frequent question you get when discussing cylinder heads with a customer?" His answer? "How much air will they flow or how many cc's are the ports?" Stop right here. Note, nothing was said about port shape, surface finish, airflow quality, cross section vs. torque range, combustion chamber shape, or any other characteristic of potential impact on optimizing power. Only "how much airflow" and "how big are the ports." What's implied is that more flow must mean the better when, in fact, both expectations can be misleading, if not wrong.


( 215 cc's is not too big for an honest street application and does not automaticly mean a high rpm "race" application. Some just like to step it up a bit )

[blaktopr]

Yes, airflow quality more inportant as airflow quantity. That should be the discussion in this thread not a pissing contest. Everyone is in the persuit of better times. What we can do is evaluate our own work and try new things to better ourselves in that persuit. Its funny cause the customers only want to know those two things about their heads, Steve, cause I feel we can be more than that. Educated customers. I hate seeing people get taken for a ride cause their machineist and magazine articles. Here we can discuss the facts and ideas to make good decisions and progress for ourselves. Maybe Larry is also trying to say through example is that for strong street motors, any cast iron head can me made to perform very well for the intended et that one is trying to persue, even some strip terrors too. That we dont need to go to the aluminum head yet if 10's, 11's, or 12's is your goal. Maybe im wrong, Larry. But, on the other hand, and with respect to the "example man" who is to say that his head is totally correct in respect to flow quality and quantity. How many items were changed in the past for the persuit of better times. Maybe he has been chasing the perfect setup to complement the cylinder head profile that he has. Maybe that is why not everyone can copy the same combo and get the same results? Depends on who ports the heads. Same cc's same flow but different?? Maybe thats why lots of people change so much. If you know what you are working with inside your head, a better idea of direction to take with selection of other parts. This even goes for the aluminum heads too. Any combo can work or appear to work for low rpm and high. Just cause a motor makes really good power under 6000 doesnt mean it works well. Proper port work may get even better results. We dont know cause not enough testing. We can only discuss our findings. I ramble, sorry. But seriously.......................I would beat all of u in a race....with a d-port 400. Just playing!!! lets get technical.............also without using magazine articles as the arguing points.

[Skip Fix]

blaktopr you bring up the same points I have in many of these discussions where smaller is automatically assumed to have better velocity and quality just based on port size alone. Even using the same head different porters are going to have different size and shape ports to get the same airflow, but as the Pro Stock guys(and the recent article on Chevy head testing I mentioned) found they may have varied power with similar flow due to those other factors. As you have stated it is just not that simple.

"the size, the shape, the flow??? MMMMMMMMMMM. How bout a question, can a 250cc intake port have the same velocity as a 175cc intake port. How and why?" Shape and entrance into the chamber are definite possibilities.

I've been called ignorant for suggesting that port cc is not the end all factor.You might get the same label for questioning that.