[i82much]

Originally Posted by PAUL K

These are great heads for a serious effort high performance Pontiac. They are copies of what we consider our "standard pushrod location race head". They differ from other commercially available CNC heads in many ways. But what we are most proud of (other than their power producing potential) is the lack of pushrod tubes and head bolt sleeves. For years I've rolled my eyes looking at ported heads that slice away the head bolt boss. The loss of integrity of the casting and potential for sucking oil far out weighs any power gain found from removing the head bolt boss. The pushrod tubes are almost always in the way of the pushrod or a shop installs a tube that is excessively large and reduces the CSA area at a critical point. These heads have made over 800 horsepower on stock block builds and have run 5.0 in the 1/8 on a 3300 lbs. street driven nitrous car.

The port volume is close to 250 cc.

Port window has been optimized to work with a Victor manifold.

That's a modified cast 72 CC chamber in the picture. We have done these heads with the Edelbrock CNC chamber and 87 CC ports. Valve size can be varied per application.

Delivery times are a mess due to parts availability, folks not wanting to work and the people that are willing to work being over loaded.

do you have a different program for someone that wants to run a T2, RPM, or Northwind?

[slowbird]

Originally Posted by i82much

do you have a different program for someone that wants to run a T2, RPM, or Northwind?

I think only intake you listed that might have an issue is the T2 and just because of lack of material in the roof on those intakes.

[Gach]

Originally Posted by PAUL K

These are great heads for a serious effort high performance Pontiac. They are copies of what we consider our "standard pushrod location race head". They differ from other commercially available CNC heads in many ways. But what we are most proud of (other than their power producing potential) is the lack of pushrod tubes and head bolt sleeves. For years I've rolled my eyes looking at ported heads that slice away the head bolt boss. The loss of integrity of the casting and potential for sucking oil far out weighs any power gain found from removing the head bolt boss. The pushrod tubes are almost always in the way of the pushrod or a shop installs a tube that is excessively large and reduces the CSA area at a critical point. These heads have made over 800 horsepower on stock block builds and have run 5.0 in the 1/8 on a 3300 lbs. street driven nitrous car.

The port volume is close to 250 cc.

Port window has been optimized to work with a Victor manifold.

That's a modified cast 72 CC chamber in the picture. We have done these heads with the Edelbrock CNC chamber and 87 CC ports. Valve size can be varied per application.

Delivery times are a mess due to parts availability, folks not wanting to work and the people that are willing to work being over loaded.

If you don’t mind me asking whats a set go for, that’!! make 700 hp with a Victor intake on a 505. Set up for right cam springs.

[Gach]

Got a friend I’m doing a 505 for and he’s about ready to pull the tiger. Oh 72 cc chamber Text me if you prefer.

[slowbird]

Originally Posted by Gach

Got a friend I’m doing a 505 for and he’s about ready to pull the tiger. Oh 72 cc chamber Text me if you prefer.

Keep your phone on you, I'm sure Paul will be contacting you very soon.

[PAUL K]

Originally Posted by i82much

do you have a different program for someone that wants to run a T2, RPM, or Northwind?

We don't have a CNC program for the smaller heads, all those get done the old fashion way. The Torker II and RPM need a considerable amount of work to keep up with our 318 cfm heads, the Northwind would be a better choice.

[i82much]

Originally Posted by PAUL K

We don't have a CNC program for the smaller heads, all those get done the old fashion way. The Torker II and RPM need a considerable amount of work to keep up with our 318 cfm heads, the Northwind would be a better choice.

Thanks!