| FAQ |
| Members List |
| Social Groups |
| Calendar |
| Search |
| Today's Posts |
|
|
|
#1
05-02-2005, 09:44 AM
|
||||
|
||||
Just got my new 406 running this weekend. Id like some feedback on if my oil pressure is OK.
Cold start at 1200 RPM, oil pressure is 60 psi. When motor gets hot, the oil pressure drops to 20psi at 800 rpm, 40 at 2K, 45 at 2500, 50psi at 3,000. No metal found in first oil filter, engine runs well and has good power, no strange noises. Melling 54DS oil pump, 6.8 rods, ross pistons, FM4040M mains, Clevite 743H rods, brng clearances were .002". thanks, robertg
__________________
I could explain all this to the girl at the parts store, but she'd probably call the asylum. White '67 LeMans 407/TH350/Ford 3.89... RIP Red '67 LeMans. 407/TH400/Ford 3.25 |
|
#2
05-02-2005, 06:01 PM
|
|||
|
|||
|
Those are the numbers I get on my 455 and have had since I rebuilt it a few years ago. When I was rebuilding it, I noticed the lifter clearance in each bore was 0.002" which seemed high to me (you could feel the lifter rocking in the bore) but it was within Pontiac's spec (just). I wonder if the oil leakage past 16 sloppy lifters explains the pressure being somewhat low? Anyway, I don't worry about it.
|
|
#3
05-03-2005, 11:02 AM
|
||||
|
||||
|
Next to distributor at oil galley. Gauge is an Equuis gauge I bought at O'Reilliys about 2 months ago. Should I bench-test with another gauge? Sometimes the pressure "flutters" like the relief spring is oscillating or something.
thnx robertg
__________________
I could explain all this to the girl at the parts store, but she'd probably call the asylum. White '67 LeMans 407/TH350/Ford 3.89... RIP Red '67 LeMans. 407/TH400/Ford 3.25 |
|
#4
05-03-2005, 09:42 AM
|
|||
|
|||
|
Chip,
Where is the oil pressure line tapped into, filter housing or next to distributor? |
|
#5
05-03-2005, 11:24 AM
|
|||
|
|||
|
I get very similar pressures and I have the Eagle stroker kit in mine. I did run a second gauage at the oil filter housing to double check and it was approx. 8-10lbs higher. I think we should be OK. I will consider these pressures normal for my set up and if they drop outside my 'normal' range I'll have to address it.
|
|
#6
05-02-2005, 09:44 AM
|
||||
|
||||
|
Just got my new 406 running this weekend. Id like some feedback on if my oil pressure is OK.
Cold start at 1200 RPM, oil pressure is 60 psi. When motor gets hot, the oil pressure drops to 20psi at 800 rpm, 40 at 2K, 45 at 2500, 50psi at 3,000. No metal found in first oil filter, engine runs well and has good power, no strange noises. Melling 54DS oil pump, 6.8 rods, ross pistons, FM4040M mains, Clevite 743H rods, brng clearances were .002". thanks, robertg
__________________
I could explain all this to the girl at the parts store, but she'd probably call the asylum. White '67 LeMans 407/TH350/Ford 3.89... RIP Red '67 LeMans. 407/TH400/Ford 3.25 |
|
#7
05-03-2005, 06:31 AM
|
||||
|
||||
|
Thanks for the replies,
Using Castrol 10W30 and AC Delco filter. After 100 miles I'm going to cut that filter open and look for metal. If no metal found, I'll install a WIX filter and top the oil off, change in another 400 miles. Hopefully I'm being paranoid, this engine has crazy power and I want to enjoy it. Thanks!
__________________
I could explain all this to the girl at the parts store, but she'd probably call the asylum. White '67 LeMans 407/TH350/Ford 3.89... RIP Red '67 LeMans. 407/TH400/Ford 3.25 |
|
#8
05-02-2005, 04:00 PM
|
||||
|
||||
|
Sounds good to me too
|
|
#9
05-03-2005, 01:36 PM
|
||||
|
||||
|
sounds like a good idea. My 350 in the car previously had the gauge hooked to the filter housing. I'll try that as I have time. Keep the ideas coming, what else should I look for.
thanks!
__________________
I could explain all this to the girl at the parts store, but she'd probably call the asylum. White '67 LeMans 407/TH350/Ford 3.89... RIP Red '67 LeMans. 407/TH400/Ford 3.25 |
|
#10
05-03-2005, 04:06 AM
|
|||
|
|||
|
What weight oil would you use to bring the oil pressure up?
|
|
#11
05-02-2005, 10:28 PM
|
||||
|
||||
|
Although I don't think you'll have a problem with those pressures, the hot numbers seem on the low side. You didn't say what oil- synthetic? What viscosity? Any out-of-the-ordinary lifter situation- rollers with no lifter-bore restrictor, etc.?
__________________
Anybody else on this planet campaign a M/T hemi Pontiac for eleven seasons? ... or has built a record breaking DOHC hemi four cylinder Pontiac? ... or has driven a couple laps of Nuerburgring with Tri-Power Pontiac power?(back in 1967) ... or has a Pontiac born the same year as Jim Wangers? (1926} 
|
|
#12
05-03-2005, 04:12 AM
|
||||
|
||||
|
A switch from 10-30 to 15-40 or 20-50 will bring the pressure up but, how low is it and what is it covering up. Mine likes 10-40. 15+ at hot idle and 55 at cruise.
__________________
 frittering and wasting the hours in an off hand way.... 1969 GTO, 455ci, 230/236 Pontiac Dude's "Butcher Special" Comp hyd roller cam with Crower HIPPO solid roller lifters, Q-jet, Edelbrock P4B-QJ, Doug's headers, ported 6X-8 (97cc) heads, TKO600, 3.73 geared Eaton Tru-Trac 8.5", hydroboost, rear disc brakes......and my greatest mechanical feat....a new heater core.
|
|
#13
05-02-2005, 03:53 PM
|
||||
|
||||
|
Sounds ok to me...
__________________
North Dakotas fastest REAL GTO 10.10 @ 131 MPH in the 1/4 Hoping to get it back together some year. www.jandjrepairandrestoration |
|
#14
05-02-2005, 04:14 PM
|
||||
|
||||
|
What weight oil are you using?
__________________
frittering and wasting the hours in an off hand way.... 1969 GTO, 455ci, 230/236 Pontiac Dude's "Butcher Special" Comp hyd roller cam with Crower HIPPO solid roller lifters, Q-jet, Edelbrock P4B-QJ, Doug's headers, ported 6X-8 (97cc) heads, TKO600, 3.73 geared Eaton Tru-Trac 8.5", hydroboost, rear disc brakes......and my greatest mechanical feat....a new heater core.
|
| Reply |
| Thread Tools | |
| Display Modes | |
|
|
The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.
Hybrid Mode
