[harry k]

So i get a customer in seeking more power (long story short)
Lately since there has been threads in here that cast iron intake manifolds perform better than aluminum intakes in mild combos
Here is a appple to apple dyno test.

as arrived cast iron intake








19 RWHP GAIN @3700RPM


22 RW TQ @2500 RPM


Sharing my testing here, if i get any smart a__ reply's back regarding the integrity of my dyno testing i am shutting this thread.

[Rocky Rotella]

Harry, what's the aluminum manifold? Crosswind?

[harry k]

yes Rocky, its a copy cat of Crosswind.

[goatless]

Any other adjustments made to the tuning of the car? Is that a carb adapter on the iron intake? I'd be curious to see back to back runs with a spread bore carb.

[dmac]

I must be stupid, as I've been told, but which result is which?

[harry k]

Originally Posted by dmac

I must be stupid, as I've been told, but which result is which?

the red graph is iron intake and blue is aluminum intake.

[harry k]

Originally Posted by goatless

Any other adjustments made to the tuning of the car? Is that a carb adapter on the iron intake? I'd be curious to see back to back runs with a spread bore carb.

the stock intake pull seen here was at its opimal tune,
the black thingee under the carb is 3/8 spread bore spacer with 4150 sealing gasket was used under the square bore Edelbrock carb as it arrived to me.

[goatless]

Originally Posted by harry k

the stock intake pull seen here was at its opimal tune,
the black thingee under the carb is 3/8 spread bore spacer with 4150 sealing gasket was used under the square bore Edelbrock carb as it arrived to me.

While I don't doubt the aluminum intake has the ability to make more power, I can't help but wonder if the square bore carb adapted onto the spread bore iron intake may have hurt it's power to some extent?

[Half-Inch Stud]

The TQ curve shows an improved inhale across a broad RPM.

Personally, i'd like to see what a Q-JET does. ( should be same, right?)

[harry k]

Originally Posted by Half-Inch Stud

The TQ curve shows an improved inhale across a broad RPM.

Personally, i'd like to see what a Q-JET does. ( should be same, right?)

noticible difference in power.

"Personally, i'd like to see what a Q-JET does."
would fry's go with that shake
its not equiped with Q-jet and i am not spending my dime on this one.

[Half-Inch Stud]

Originally Posted by Half-Inch Stud

The TQ curve shows an improved inhale across a broad RPM. Personally, i'd like to see what a Q-JET does. ( should be same, right?)

How many pages & posturing for bicker ?! POST#6 in Expanded form;

Squarebore carb on a spreadbore intake got measured; not good.

Spreadbore on the factory Intake would reveal performance.

Squarebore carb on Squarebore intake got measured; is fine.

no ifs, and or butts, no bull, no OBFUSCATION. Just plain clarity. HIS

[Firebob]

Harry, I know you can't spend all day doing this but I notice that sometimes you get better numbers on the second pull just because(maybe because all the cr@p gets blown out on the first pull). I also wonder what a regular performer would do against the high rise? I ask because I'm thinking about going back to the regular Performer instead of the RPM but I don't want to if I'll be giving up that much.

[harry k]

Originally Posted by Firebob

Harry, I know you can't spend all day doing this but I notice that sometimes you get better numbers on the second pull just because(maybe because all the cr@p gets blown out on the first pull). I also wonder what a regular performer would do against the high rise? I ask because I'm thinking about going back to the regular Performer instead of the RPM but I don't want to if I'll be giving up that much.

true if car is carboned up,unloading it wot on dyno you blow the carbon nicely away and the second pull will be miniscule higher.

"I also wonder what a regular performer would do against the high rise? I ask because I'm thinking about going back to the regular Performer instead of the RPM but I don't want to if I'll be giving up that much."
grab your performer intake & comon by and well do exactly what you want.

[dmac]

That looks great for street use. A lot of the other results extend the test out ot 600o rpm, and it does look like the lines begin to converge at higher rpms, and maybe the lines cross at some point, but for daily driving the extra torque from 2000-5000 rpms is enough to notice, at least on that cam/head combo. I know the edelbrock used to claim just about the difference your test shows between their aluminum and stock manifolds.

Based on the 350 max torque numbers, I assume this is close to a stock motor, with close to stock cam specs.

[Rocky Rotella]

Harry, can you share combo details?

[harry k]

Originally Posted by Rocky Rotella

Harry, can you share combo details?

As much as i know i will:
its a 400ci maybe 30over rebuild by local engine builder machine shop,no relation to me
it has 670 casting heads and 175psi cyl pressure i checked and its doing fine on our Ca. piss 91 octane, i dont know whats the pistons used in it (meaning SCR where it is) cam wise again i dont have details but it has 16to17" vacuum at idle and its 4spd manual car
the best part get this, its in a 1964 Chevrolet Impalla SS.

[harry k]

Originally Posted by harry k

So i get a customer in seeking more power (long story short)
Here is a appple to apple dyno test.

Originally Posted by Cliff R

The results are pretty close to what we found using a square bore carb on a factory spread bore intake (unmodified) with an adapter/spacer. The spacer/adapter is a significant miss-match between the two parts. The last time I tested a deal like that it cost us just under 30hp on a pretty stout 455 making just over 500hp.
Cliff

Irelevent mismatch or not, the test was here again apple to apple
1 more time remove cast iron intake & install aluminum intake with no other changes

[nadine]

The results are pretty close to what we found using a square bore carb on a factory spread bore intake (unmodified) with an adapter/spacer. The spacer/adapter is a significant miss-match between the two parts. The last time I tested a deal like that it cost us just under 30hp on a pretty stout 455 making just over 500hp.

I have seen the same Loss of power as Cliff did. On a Boss 351 engine and a Boss 302
with a Shelby 8V manifold when I installed open spacers on four hole manifolds.

Ken Maisano

[GOAT WHORE]

Originally Posted by harry k

Irelevent mismatch or not, the test was here again apple to apple
1 more time remove cast iron intake and 3/8" spacer & install aluminum intake with no other changes

Fixed it for you
Thanks for taking the time to post.

[242177P]

That crossover on the 67 intake has seen some serious temperatures. Is the exhaust flapper stuck in the closed position??



Aluminum intake doesn't have a crossover.
Apples to... coconuts.