[Mr Twister]

I'm making some minor changes to try to get my T/A to run better at idle an low rpms. Currently idles at 1400 and soots up the rear valance. During spirited driving it pulls hard for what it is. Its a 455 with 4X-7h heads, Qjet, RA3 manifolds, lunati 301/308 (231/240) .424/.424 lift (as reported by the seller). It has been suggested in other threads
I need more compression and the cam is a little big. The plan is: first rhoades lifters, then carb tuning and curving the distributor.
I got some new lifters from Rhoades last week and want to use the existing cam. With all the failed HFT cams lately, I want to coat the lifters. I got the lifters with the oil hole on the bottom. Recommendations are appreciated.
-

[chuckies76ta]

Why is it idling so high? And if it's soot, that would indicate a rich mixture. I'd be curious on your timing setup and air/fuel ratio.
As far as coating lifters and the cam, I would think Comp cam lube should work fine. https://www.compcams.com/cam-lifter-...oz-bottle.html

[HWYSTR455]

Honestly, I would disassemble the lifters and clean the heck out of them before putting them into service, amazing the crap you will find in there.

Rhoads should use an e-clip, so easy to take apart. Do one at a time.

As for lube, me personally, I use assembly lube. I know a lot of people like the grey moly stuff and glob it on there, but assembly lube has less side effects and has many positive attributes. That moly stuff clogs filters fast.

Go to Summit or wherever and search for 'engine assembly lubes'.

I know people have a lot of different opinions on the lubes but IMO, the engine assembly lubes are the best to use. And contrary to popular belief, even if the carrier runs off, the lubricant remains on the part where applied.

Sealed Power and Permatex Ultra slick might be available in parts stores, both are good. There's no reason to buy some whiz-bang expensive brand, crazy what they charge for some of that stuff.



.

[Mr Twister]

I was leaning toward a professionally applied anti friction coating like DLC. I plan to get a kit from Cliffs predecessor and going through the carb. I just got the car and only had a few weeks to drive it before it got stored for the winter.

[HWYSTR455]

I guess a friction coating isn't a bad idea, but it may cost as much as a cam and lifters.

I think if you do it right there shouldn't be any concern over a cam/lifter failure.


.

[ANDYA]

This past summer I broke in a Mellling 068 with Crower lifters. I used the Driven GP-1 assembly gel . This stuff was unbelievable. Stays where you put it and never drips off like other brands. As a test I coated a lobe on a used cam I have in the basement and left it that way for months. Eventually I wiped off the lobe and put the cam back in storage. Absolutely nothing dripped off. Broke the cam in with 1.65 rockers and inner springs removed. Used Penn Grade 30 wt break in oil and a bottle of GM EOS. Break in went perfect and I have since put about 500 miles on the motor.

[HWYSTR455]

The Torco stuff is kind of a gel, but almost all have some type of 'carrier' which has no impact on the properties of the lube.

The newer stuff sticks like anything in the past comes even close to. It's that much better. You don't have to glob it on, a very thin coat and done. That's why it comes in smaller amount packaging.

Moly can dry up, and it doesn't embed as well as the newer stuff. I can 'wipe off' easily.

The newer survives much longer during startups, as well as while turning the engine over by hand when adjusting rockers for first time.

Use specifically design engine assembly lube and don't look back. It's that easy.


.

[Formulas]

Again .. You can lead a horse to water... Goes on like paint dries doesnt fall off with a little oil splash ... i even coated my pistons, bottom of the cylinders under ring travel fogged where rings ride coated all cam lobes, main,rod,cam bearings, hit lifter bores with 842

I was actuall very suprized with no smoke at all at first run no detectable blowby with PCV plugged

Used 842 in another 2 engines nothing negative to report they are still together

2 to 3 engines one can

[MarkS57]

Originally Posted by ANDYA

This past summer I broke in a Mellling 068 with Crower lifters. I used the Driven GP-1 assembly gel . This stuff was unbelievable. Stays where you put it and never drips off like other brands. As a test I coated a lobe on a used cam I have in the basement and left it that way for months. Eventually I wiped off the lobe and put the cam back in storage. Absolutely nothing dripped off. Broke the cam in with 1.65 rockers and inner springs removed. Used Penn Grade 30 wt break in oil and a bottle of GM EOS. Break in went perfect and I have since put about 500 miles on the motor.

I am also fan of Driven products. Last 2 HFT cam swaps I did I used the Driven assembly grease product.

[Jay S]

A DLC coating is going to run $600 or $800. Finding a place that will even want to do it is probably an even bigger issue.

The oiling feature on Rhoad uses is a groove on the outside. It isn’t a EDM hole on the face.

You might look into having the lifter Cryoed. It changes the grain structure and makes the lifters tougher, and is cheap to do.

Soots sounds like it is running lean, you probably have a tuning issue mixed in with how it currently runs.

The only Lunati cam I can think of that was .424” lift was their 744 musclecar cam that had the LSA moved into 108*. I think it was 224/236 at .050”. Or something close to that.

[Jay S]

Originally Posted by Jay S

Soots sounds like it is running lean, you probably have a tuning issue mixed in with how it currently runs.

Sorry, that was suppose to say rich not lean.

You should look at the plugs and see how they are working. It could be they are a bit hot for the cam and compression.

[steve25]

That cam in that size motor should not need to idle at 1400 rpm.

I have 3 important questions.

1) what is your initial timing at?

2) how much vacuum do you have at idle?

3) what is the motors hot cranking compression ?

[Mr Twister]

I did not attempt any tuning as i lost all my tools in a fire. So I've been buying stuff as I go. I had no idea that coating was so pricey. I need to open the box from Rhoades and see what the lifter feet look like, their website said super lube and i guess thats a groove on the side, I assumed a hole like other brands.
EDIT- I opened the box and no oil hole and they are absolutely filthy. Seller said cam was Lunati 10704

[Formulas]

Clean well and use

[Jay S]

10704 was the same RA3 musclecar replacement Lunati cam I was referring too. They were 220/[email protected]” with a 110 LSA. It really isn’t a big cam in a 455, it should be able to idle at 600 to 800 RPM with a decent tune and a good lopey idle. It you use Rhoad’s lifters it probably won’t lope at all.

[steve25]

Also if the motor is idling and or running so rich that your getting soot on your rear valence then your not doing the rings and cylinder walls any good in terms of ware.

[HWYSTR455]

I'm in the camp of bad cam cores and lifters during a period of time causing cam wipes at start up. You can do all the wiz-bang stuff and still end up with a wiped cam. That's why I say take the chance and pull the trigger using 'conventional' methods, will be less waste of time & money.

If you have older stock type cam, during the time of the 'issues', then there's nothing you can do to prevent failure. But, you might get lucky.

Honestly, you're better off just buying a new cam, they corrected the issue(s), I no longer hear folks complaining about wiped cams.

I was assuming the high idle was for cam break in, so didn't think anything of it.


.

[steve25]

If your going to try and reuse that cam by breaking in new lifters on it then don’t bother buying and using any moly type lube because the lobes have no pours any more to hold onto moly lube with.

Just get a greased based cam break in lube.

[77 TRASHCAN]

Originally Posted by steve25

If your going to try and reuse that cam by breaking in new lifters on it then don’t bother buying and using any moly type lube because the lobes have no pours any more to hold onto moly lube with.

Just get a greased based cam break in lube.

Good point, Steve.
The moly lube I've used is Moroso moly paste. It seemed like a heavy grease with moly in it....couldn't hurt anything, apply sparingly.

[PontiacHO]

I used Isky Rev-Lub on my new cam and lifter faces. Just enough to cover the surface. I was surprised to see what that looked like in the break in oil after the cam break in run. I know it’s a must to have it but I’d bet it has clogged up some oil filters and lifter galleys!!