| FAQ |
| Members List |
| Social Groups |
| Calendar |
| Search |
| Today's Posts |
|
#1
07-13-2010, 08:06 AM
|
||||
|
||||
picture of trunk weatherstrip needed
Does any one have a picture of the trunk weatherstrip installed on there 69? I want to make sure mine is in correctly before I glue it thanks!.
__________________
1969 GTO street strip project 11.1 forged 461, highport heads 1995 Trans-am 420 ci sb 14:1 compression 9"ford 9.89@132 1.34 60ft SOLD! |
|
#2
07-13-2010, 11:18 PM
|
||||
|
||||
|
I can try to get some pics tommorow. You wouldn't believe the number of people that put it in upside down! I've even seen it upside down on concourse cars at the nationals! Scott
|
|
#3
07-13-2010, 11:37 PM
|
||||
|
||||
|
that would be great,this car was a basket case so I had no reference.
__________________
1969 GTO street strip project 11.1 forged 461, highport heads 1995 Trans-am 420 ci sb 14:1 compression 9"ford 9.89@132 1.34 60ft SOLD! |
|
#4
07-13-2010, 11:40 PM
|
|||
|
|||
|
Here you go:
__________________
Patton Glade 70Post Restorations Austin, TX 64-72 GM A-Body Gas Tank Pads http://classicoldsmobile.com/forums/...tion-item.html |
|
#5
07-14-2010, 06:48 PM
|
||||
|
||||
|
so it curves out away from the trunk opening?how about the lip does it go under or over the trunk flange?
__________________
1969 GTO street strip project 11.1 forged 461, highport heads 1995 Trans-am 420 ci sb 14:1 compression 9"ford 9.89@132 1.34 60ft SOLD! |
|
#6
07-14-2010, 09:05 PM
|
|||
|
|||
|
Yes---the top edge points outwards as you asked.
On the two lips about midway down....I'll have to check on a car here. Have temporary access to a computer right now as mine crashed so it may be a bit 'til I can check and respond. Maybe someone else can pipe in in the meantime. THanks
__________________
Patton Glade 70Post Restorations Austin, TX 64-72 GM A-Body Gas Tank Pads http://classicoldsmobile.com/forums/...tion-item.html |
|
#7
07-17-2010, 09:07 AM
|
||||
|
||||
|
Not sure if you have it in yet or not, but the cross section pic provided is very good and you should find it very easy and logical when you actually go to install. The rubber protrusion fits under a metal lip on the inside and the seal curves away from the trunk opening as mentioned.
Be sure to carefully inspect the gasket channel all the way around and repair any holes you find. Water will find its way even through a small pinhole under the gasket.
__________________
1969 Lemans vert, matador red, 462 CI, 3.07 12-bolt posi 1974 455 TA, admiralty blue/red interior HPP "cover car" - sold "The best way to show a car is to drive it" |
|
#8
07-17-2010, 12:47 PM
|
||||
|
||||
|
yes its installed picture helped a ton thanks,new mexico car so no rust and it was just painted a month back.Im just assembling it now.
__________________
1969 GTO street strip project 11.1 forged 461, highport heads 1995 Trans-am 420 ci sb 14:1 compression 9"ford 9.89@132 1.34 60ft SOLD! |
|
#9
04-29-2015, 01:38 PM
|
||||
|
||||
Thanks for the picture! I was trying to install it wrong.
__________________
When I'm paid, I always follow my job through...you know that. http://www.youtube.com/watch?v=Al2b-...eature=related |
|
#10
04-30-2015, 08:33 AM
|
|||
|
|||
|
I did'nt know it needed to be glued. I've done a few and just forced them in...
|
| Reply |
|
|
The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.
Linear Mode
